다운로드
다운로드

매뉴얼, 데이터 시트, 소프트웨어 등을 다운로드할 수 있습니다.

다운로드 유형
모델 또는 키워드

MDO4000

The most powerful mixed domain oscilloscope, the MDO4000 combines up to six instruments including options like a function generator and a built-in spectrum analyzer. Unlike any other instrument, it can synchronize RF, analog and digital channels – giving unprecedented insight into your design.
See all oscilloscopes »

Bandwidth

Up to 1 GHz

Record length

20 Mpoints

Analog channels

4

Sample Rate

Up to 5 GS/s

 

강력한 스코프 그 이상의 기능 제공

Thumbnail

오늘날의 엔지니어링 디자인은 프로세서, 시리얼 버스 및 무선 인터페이스의 복합체로 이루어져 있습니다. MDO4000C의 중심에는 인기 높은 텍트로닉스 오실로스코프와 확장 가능한 플랫폼이 있습니다. 해당 기능을 테스트 목적에 맞게 사용자 정의할 수 있습니다. 16가지 로직 채널, 50MHz 임의/함수 발생기, 프로토콜 분석 및 진정한 통합형 하드웨어 3GHz 또는 6GHz 스펙트럼 분석기를 추가하여 복합 디자인 과제를 해결합니다.

주요 특징

  • 트리거된 통합형 획득 시스템 - 시간 및 주파수 도메인에서 125가지가 넘는 트리거 조합 구현
  • Wave Inspector® 컨트롤을 포함하는 20M 포인트 레코드 길이
  • 진정한 스펙트럼 분석기 하드웨어로 실제 스펙트럼 분석 가능
  • 확장 가능한 기능으로 미래에 대한 뛰어난 유용성 보장

정확한 측정

Thumbnail

간단히 말해서 MDO 시리즈 스코프는 업계에서 가장 정확한 측정을 제공하도록 디자인되어 있으며 탁월한 디자인까지 구현합니다. 많은 다른 장비들이 디스플레이 데이터를 측정하고 스냅숏 보기만 제공하지만 MDO4000C는 실제 획득 데이터를 측정합니다. 거기서 끝나지 않습니다. 많은 경쟁업체 제품보다 더 나은 사양을 보장하므로 MDO4000C은 믿을 수 있는 측정 결과를 제공합니다. 결과적으로 측정 정밀도는 디자인 무결성에도 영향을 줍니다. 정밀도가 충족되지 않는다면 고려할 필요가 없을 것입니다.

업계의 선두적 프로브 – 모든 구매 제품에 포함

Thumbnail

측정 신호 경로를 검사할 때 프로브는 간과해서는 안 되는 핵심 요소입니다. MDO4000C을 구입하면 업계 최고의 프로브도 보너스로 받는 셈입니다. 업계 최고 수준의 3.9pF 로드와 오실로스코프에 적합한 대역폭을 자랑하는 TPP 시리즈 프로브는 여러분이 원하던 일상에서 사용하기 좋은 프로브입니다.

주요 특징

  • 아날로그 채널당 1개의 표준 TPP 시리즈 프로브 포함
  • 업계 최고의 낮은 프로브 부하 3.9pF 유지
  • 스코프 대역폭에 맞게 500MHz 또는 1GHz 프로브 대역폭 제공

무선 측정 - 완전히 새로운 레벨 지원

Thumbnail

RF 측정 결과가 어떻든, 통합형 하드웨어 스펙트럼 분석기 및 SignalVu-PC 소프트웨어가 내장된 MDO4000C 오실로스코프를 사용하면 결과에 만족하게 될 것입니다. FFT “스펙트럼 분석”을 제공하는 오실로스코프와 달리, 진정한 스펙트럼 분석기가 통합된 MDO4000C는 아날로그, 디지털 및 스펙트럼 분석기 채널에서 통합되는 트리거된 획득 시스템을 제공합니다. 최대 6GHz의 RF 측정을 수행하고 진정한 장점은 주파수 도메인의 이벤트와 이를 일으킨 시간 도메인 현상의 상관관계를 파악할 수 있습니다.

주요 특징

  • 3GHz 또는 6GHz 스펙트럼 분석기 옵션 사용 가능
  • 업계에서 유일한 진정한 통합형 스펙트럼 분석기 하드웨어
  • 아날로그 및 디지털 파형과 동기화된 스펙트럼 분석 시간

Accidents happen. Make sure you're protected.

텍트로닉스는 잦은 장비 고장과 손상을 보장할 수 있도록 업계 최초의 장비 보호 플랜을 제공합니다. 이 보장 플랜에는 화면 손상, 얼룩, 깨진 마운트, 정전기 방전 또는 전자 장치의 과입력 사고 등이 포함됩니다. 텍트로닉스의 토털 보호 플랜(Total Protection Plan)으로 수리 또는 교체 비용을 줄여 보십시오. 자세한 사항은 비디오를 시청하거나 아래를 클릭하여 확인하십시오.

자세히 보기

경쟁 제품 비교

Thumbnail

MDO4000C 시리즈
오실로스코프

Thumbnail

InfiniiVision 4000 X-시리즈
오실로스코프

최대 4개의 채널에서 20M 포인트

Record Length

최대 4개의 채널에서 2M 포인트

파형 데이터

측정

표시된 데이터

전용 하드웨어 스펙트럼 분석기

Spectrum Analyzer

없음.
오실로스코프 입력에서 게이트된 FFT 사용

9kHz - 6GHz

RF 주파수 범위

수평 시간 스케일에 따라 제한되는 최대 범위
< 15GHz

최대 1GHz - 1년 보증

패시브 프로브 포함

700MHz - 90일 보증

3.9pF

프로브 용량 부하

9.5pF

 

모델 아날로그 대역폭 샘플링 속도 레코드 길이 아날로그 채널 디지털 채널 스펙트럼 분석기 함수 발생기 출력 정가
MDO4024C 200MHz 2.5GS/s 20M 포인트 4 16(옵션) 최대 6GHz

1(옵션)

US $7,430
구성 및 견적
MDO4034C 350MHz 2.5GS/s 20M 포인트 4 16(옵션) 최대 6GHz

1(옵션)

US $11,500
구성 및 견적
MDO4054C 500MHz 2.5GS/s 20M 포인트 4 16(옵션) 최대 6GHz

1(옵션)

US $15,200
구성 및 견적
MDO4104C 1GHz 2.5~5GS/s 20M 포인트 4 16(옵션) 최대 6GHz

1(옵션)

US $18,700
구성 및 견적
모델 아날로그 대역폭 샘플링 속도 레코드 길이 아날로그 채널 디지털 채널 스펙트럼 분석기 함수 발생기 출력 정가
MDO4024C 200MHz 2.5GS/s 20M 포인트 4 16(옵션) 최대 6GHz

1(옵션)

US $7,430
구성 및 견적
MDO4034C 350MHz 2.5GS/s 20M 포인트 4 16(옵션) 최대 6GHz

1(옵션)

US $11,500
구성 및 견적
MDO4054C 500MHz 2.5GS/s 20M 포인트 4 16(옵션) 최대 6GHz

1(옵션)

US $15,200
구성 및 견적
MDO4104C 1GHz 2.5~5GS/s 20M 포인트 4 16(옵션) 최대 6GHz

1(옵션)

US $18,700
구성 및 견적
  Tektronix
MDO4000C
Tektronix
MDO3000
Keysight
4000 X-시리즈
LeCroy
HDO4000
R&S
RTE1000 시리즈
R&S
RTM2000 시리즈
Bandwidth 200MHz - 1GHz 100MHz - 1GHz 200MHz - 1.5GHz 200MHz - 1GHz 200MHz - 1GHz 200MHz - 1GHz
Upgradeable Bandwidth -- --
아날로그 채널 4 2 또는 4 2 또는 4 2 또는 4 2 또는 4 2 또는 4
아날로그 샘플링 속도 최대 5GS/s 최대 5GS/s 최대 5GS/s 최대 2.5GS/s 최대 5GS/s 최대 5GS/s
표준 레코드 길이(모든 채널) 20M 10M 2M 12.5M 10M 10M
통합 임의/함수 발생기 50MHz(옵션) 50MHz(옵션) 20MHz(옵션) -- -- --
통합 로직 채널(MSO) 16개(옵션) 16개(옵션) 16개(옵션) 16개(옵션) 16개(옵션) 16개(옵션)
통합형 하드웨어 스펙트럼 분석기 최대 6GHz(옵션) 최대 3GHz(옵션) -- -- -- --
아날로그, 디지털 및 RF의 전체 동기화 -- -- -- -- --
표준 프로브 최대 1GHz 패시브 최대 1GHz 패시브 최대 700MHz 패시브 최대 500MHz 패시브 최대 500MHz 패시브 최대 500MHz 패시브
기본 보증 3년 3년 3년 3년 3년 3년

 

임베디드 시리얼 버스 트리거, 디코딩 및 분석

Thumbnail

시리얼 버스의 단일 신호에는 주소, 컨트롤, 데이터 및 클럭 정보가 포함되는 경우가 많기 때문에 원하는 이벤트를 분리하기가 어렵습니다. MDO4000C 시리즈의 시리얼 애플리케이션 모듈은 자동 트리거, 디코딩 및 검색 기능으로 시리얼 버스를 디버깅하기 위한 견고한 도구로 오실로스코프를 변환합니다.

주요 특징

  • I2C, SPI, RS-232/422/485/UART
  • CAN/CAN FD, LIN, FlexRay
  • I2S/LJ/RJ/TDM
  • MIL-STD-1553, USB, 이더넷

파워 측정 및 분석

Thumbnail

더 높은 에너지 효율성에 대한 필요성은 설계자와 테스트 장비 모두에 새로운 기준을 요구하고 있습니다. 대기 전력 제한, 더 증가한 스위칭 속도 및 신호 범위, 손실이 더 낮은 반도체 장치로 인해 테스트 상황이 새로운 극한 상황이 되는 경우가 많습니다. MDO4000C는 새롭게 출현하는 이러한 요구 사항을 해결하는 전원 테스트 솔루션을 제공합니다.

주요 특징

  • 스위칭 장치에서 파워 손실 측정
  • 리플과 노이즈 측정 및 분석
  • 전력 반도체 장치 특성화
  • 활성 전력 계수 보정 회로 디버깅

전자파 간섭(EMI) 및 전자파 적합성(EMC)

Thumbnail

설계 EMI/EMC 테스트 수행 시 항상 실패 위험이 뒤따르기 마련이며, 이 경우 일정을 못 맞추거나 예산을 초과하게 될 수 있습니다. 스펙트럼 분석기가 내장되고 아날로그, 디지털 및 RF 신호의 시간 상관 관계 측정 등이 포함된 MDO4000C를 사용하면 실험실에서 사전 컴플라이언스 테스트를 수행하여 전체 EMI 컴플라이언스 테스트를 한 번에 통과할 가능성이 대폭 높아집니다.

자동차/버스 – CAN/CAN FD 트리거, 디코딩 및 분석

Thumbnail

오늘날 자동차의 기술 요건으로는 이전보다 더 정교하고 민감한 전자 구성 요소와 시스템을 들 수 있습니다. 총 6대의 장비가 하나로 통합된 텍트로닉스의 MDO4000C는 이러한 고급 기술의 테스트 및 확인과 관련한 문제점을 해결하기 위해 개발되었습니다. 이제 하나의 장비로 다음 작업을 수행할 수 있습니다.

  • CAN FD, CAN, LIN 및 FlexRay 디버깅 및 확인
  • 하이브리드/전기차의 고전력 테스트
  • 차량 내 무선 시스템 확인
  • 새 구성 요소 평가(MEMS 센서, LED 드라이브, LED)

 

데이터 시트 소프트웨어 패키지/소프트웨어 옵션 설명 구성 및 견적 요청
액세서리 119414600
데이터 시트 설명
보기 데이터 시트 프로브 집합, RF 측정, 근거리 프로브 집합, 패시브, 휴대용
액세서리 119660900
데이터 시트 설명
보기 데이터 시트 안테나, 고무 피복, BNC 커넥터 포함, KD4 VHF, 조정되지 않음, 고무 뚜껑이 붙어 있음
액세서리 HCTEK54
데이터 시트 설명
보기 데이터 시트 하드 운반 케이스
액세서리 RMD5000
데이터 시트 설명
보기 데이터 시트 랙 마운트 키트
액세서리 TPA-N-PRE
데이터 시트 설명
외부 프리앰프, TPA 커넥터, SMA 입력
액세서리 TPA-N-VPI
데이터 시트 설명
보기 데이터 시트 N형 커넥터로 프로브 어댑터와 TekVPI 연결
데이터 시트 액세서리 설명
119414600 프로브 집합, RF 측정, 근거리 프로브 집합, 패시브, 휴대용
119660900 안테나, 고무 피복, BNC 커넥터 포함, KD4 VHF, 조정되지 않음, 고무 뚜껑이 붙어 있음
HCTEK54 하드 운반 케이스
RMD5000 랙 마운트 키트
보기 데이터 시트 TPA-N-PRE 외부 프리앰프, TPA 커넥터, SMA 입력
TPA-N-VPI N형 커넥터로 프로브 어댑터와 TekVPI 연결
Get techniques for in-system checks on Wi-Fi or other wireless modules by simultaneously viewing radio output, transceiver power supply, and RS-232 serial control bus.  Learn how to optimize …
4m 28s
Take important power supply measurements, including power quality input measurements and switching loss.  Learn important preparations, including probe deskew and current probe degauss.  See power …
4m 48s
Sometimes bad things happen to good scopes!  Ensure you've got it covered with a Total Product Protection plan from Tektronix, the only coverage plan available for test equipment with accident …
1m 2s
A side-by-side comparison of the same waveform measurements performed on both the Tektronix MDO4000C and the Keysight X 4000A shows different results. This is because the Tektronix MDO4000C …
2m 51s
The Tektronix MDO4000C mixed domain oscilloscope can measure digital, analog, and RF signals all at once enabling engineers to troubleshoot complex embedded designs more quickly. Learn more »
1m 7s
Given the approximate frequency of EMI, these techniques will help track down the source of transient RF emissions. They employ a near-field probe with the MDO4000 integrated oscilloscope and …
4m 32s
The MDO4000C offers the functions of a high-performance mainstream oscilloscope with the flexibility to add a spectrum analyzer, arbitrary / function generator, a logic analyzer, a protocol …
2m 50s
In this short video, we demo the CAN FD bus decoding process on the flexible MDO3000 oscilloscope. 
4m 28s
A side-by-side comparison of the Tektronix MDO4000C and the Keysight 4000 X-Series for one of the most common debug tasks: automated search.
2m 33s
Mixed Domain Oscilloscopes
Customizable and fully upgradeable 6-in-1 integrated oscilloscope with synchronized insights into analog, digital, and RF signals

참고자료 번호: 48W-60277-9
Datasheet
KickStart Instrument Control Software Version 2.2.1 (Windows 10, 8, 7 compatible)
KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the ability to …

부품 번호: KICKSTART-2.2.1
애플리케이션
Wi-Fi: Overview of the 802.11 Physical Layer and Transmitter Measurements
Wi-Fi is a technology that allows many electronic devices to exchange data or connect to the internet wirelessly using radio waves. The Wi-Fi Alliance defines Wi-Fi devices as any "Wireless Local Area Network (WLAN) products that are based on the …

참고자료 번호: 37W-29447-0
입문서
How to Use a Mixed Signal Oscilloscope to Test Digital Circuits
Learn how to set up a mixed signal oscilloscope and how use it in several applications including: triggering on pulse width violations, combining analog and digital waveforms to capture crosstalk, troubleshooting setup/hold violations, and checking …

참고자료 번호: 3GT-24008-4
애플리케이션 노트
Measuring Wireless Power Charging Systems for Portable Electronics
This application note shows methods for testing a Qi wireless charging system.  The device under test uses the Qi interface standard, developed by the Wireless Power Consortium. The application note explains how to use a mixed domain oscilloscope …

참고자료 번호: 48W-28034-1
애플리케이션 노트
Why does the Tkdpo2k3k4k_ReadWaveform() function in the Tkdpo2k3k4k IVI-C driver time out every time I call it when I am connected to the instrument via Ethernet? The function call works fine over USB, but over Ethernet it always times out.
The Tkdpo2k3k4k_ReadWaveform() function makes use of the Service Request Event in VISA so the scope can notify the driver when it has completed its acquisition and the waveform data is ready to be fetched as opposed to the driver polling the scope …
FAQ ID72221
How do I mount a network drive on my MDO3000 or MDO4000C oscilloscope?
This procedure also applies to the DPO/MSO/MDO4000/4000B series oscilloscopes.  Note: This Mount a network drive will not work with a direct (peer-to-peer) connection. Must go through your local DNS server. To begin, press the “Menu” button in the …
FAQ ID66201
How do I connect an SMA male output to Oscilloscopes with TekVPI BNC inputs?
Use a Tektronix part number 015-0572-XX SMA female to BNC male adapter. This adapter will plug onto the BNC on the front of the scope and connect to a SMA cable. For more questions please press the "Contact Us" button on the right of the screen.   
FAQ ID63516
I recently registered our Tektronix oscilloscope, updated the firmware and am currently trying to activate the free DVM & Frequency Counter.  I don’t see any software downloads for activating the DVM. Am I doing something wrong, or looking in the wrong spot?
After you have registered your oscilloscope on Tek.com, you should have received an email with instructions.  The email is sent to the address you used to login to tek.com.  If you haven't received the email after registration: Check your spam …
FAQ ID468046
Can active probes with TekProbe interface (such as a P6205) be used on the DPO4000B or MSO4000B series scopes?
Yes. A TPA-BNC adaptor is required for people to connect legacy TekProbe interface probes to the new TekVPI interface. The adapter works on any TekVPI scopes inlcuding the MSO/DPO/MDO4000/B/C, MSO/DPO/MDO3000 MSO/DPO2000/B or MSO/DPO5000/B or …
FAQ ID60416
What feature does the DPO4BND included?
DPO4BND includes the features for the following modules …
FAQ ID72101
When analog bandwidth is upgraded on a MDO4000C do we get new probes?
MDO4000C scopes with or less than 500MHz analog bandwidth come standard with TPP0500B 500MHz passive probes, one per channel. If upgrade to 1GHz analog bandwidth you will receive TPP1000 1GHz passive probes that come with the upgrade. 
FAQ ID72126
What is aliasing and how do I detect it and fix it on my oscilloscope?
Aliasing is basically a form of under sampling and what is displayed on the scopes is an indistinguishable waveform. The under sampled waveform is then contstructed to look like a slower frequency waveform or a flat line in the case of the sample …
FAQ ID64691
: Can the optional AFG in the MDO3000, MDO4000C and 5 Series MSO be set to sweep?
AFG in MDO3000, MDO4000C, and 5 Series MSO do not have sweep function. But a limited sweep may be created using the arbitrary function.   Example: Create a sweep from 100 KHz to 250 KHz. ArbExpress (free software on Tek.com) select Equation Editor …
FAQ ID474056
Why does my MDO4000C Series scope cause my USB flash drive to pop up with a scan and fix message on my PC?
The MDO4000C products have a new Linux kernel. The security settings of this kernel require that any USB flash drive that is removed without unmounting get tagged as a suspicious device. This can be seen when a drive is written to on the scope …
FAQ ID72166
What is the standard warranty on the MDO4000C?
The MDO4000C comes standard with a 3 year product warranty on the instrument and a 1 year warranty on the probes. Note: The MDO4000C is the first product to offer a new service option called the Total Protection Plan with options for 3 or 5 years …
FAQ ID72151
What is the maximum bit rate a decoded SPI bus can trigger on?
Different oscilloscopes have different triggering circuitry therefor the limits of what speeds can be achieved vary by scope. Please use the following table to easily look up your scope and determine your max SPI bus trigger level.  For more …
FAQ ID62256
I cannot see my signal on the Oscilloscope. What can I do?
You have many options to help diagnose this issue, below are a few suggestions to get started. If you find yourself needing more help, please connect with our Technical Support Center. You can get started by pressing the "Contact Us" button on the …
FAQ ID63686
How do I utilize the math channel feature on a DPO/MSO/MDO3000 or DPO/MSO/MDO4000 Series oscilloscope?
There are three main functionalities on the Math button on this scope. They range from Dual Waveform Math, FFT (Fast Fourier Transform), and Advance Math. These three functionalities have a range of abilities and are explained in this short YouTube …
FAQ ID64656
Is there a mictor adapter for the P6616 (logic probe for MSO5000B, MSO4000B, and MDO4000C + MDO4MSO) or P6516 (logic probe for the MSO4000 Series) or the P6316 (logic probe for MSO2000, MSO3000, MDO3000 + MDO3MSO Series)?
A mictor adapter is available from our partner Nexus Technologies. Use the mictor adapter NEX-HD2HEADER http://www.nexustechnology.com/products/laAccessories/hd2header/  
FAQ ID59716
Why do I see 16 flat lines for the MSO digital logic inputs when the same signals are displayed properly on the analog channels and all channels are setup for valid trigger threshold levels?
A common mistake for some, we first recommend verifing that the front panel MSO digital probe is properly connected by squeezing the probe's side latch buttons to un-plug, remove the probe then re-insert the probe label side up into the front panel …
FAQ ID60251
How do I reduce noise on signals using an oscilloscope?
There are many methods to reduce many types of noise on a signal. Tektronix oscilloscopes can do this through bandwidth limiting the scope input, averaging your signal, changing the sampling method to hi-resolution mode, and more. This video …
FAQ ID64706
What are the primary differences between the DPO/MSO4000B, MDO4000, MDO4000B, and MDO4000C?
The 4000 Series Mixed Domain Oscilloscopes (MDO) continues to be the only true RF/Time domain syncronized instrument on the market. The major differences between revisions of the DPO/MSO/MDO4000 Series are described below. Please note the MDO4000C …
FAQ ID72111
What cart does my scope use?
Below are the Instrument Carts that can be purchased from Tektronix.                                         K4000                                                                             K420                              K475 More information can …
FAQ ID64561
What probe interface does my oscilloscope have?
Oscilloscope series Probe interface CSA7000/CSA7000B TekConnect DPO2000 TekVPI DPO3000 …
FAQ ID64251
What is enhanced security option MDO4SEC on the MDO4000C?
Option MDO4SEC add’s enhanced instrument security to enable password protected control of turning on/off all instrument ports and instrument firmware update functionality. It is a one-time permanent upgrade.
FAQ ID72141
How can I increase the measurement accuracy using automated measurements vs cursors?
While Cursors are quick and easy at approximating measurements, using the automated measurements can give you a much better and accurate measurement results. Here are some techniques to be successful in making accurate measurements. Always use …
FAQ ID62606
How do I set up a USB bus decode?
First you must have the USB module or option key that enables USB decoding for your scope as well as proper probes. For help finding the right probe use our probe selector tool. When you go into the bus option you must select USB and then make sure …
FAQ ID64726
How do I utilize the measurement features on a DPO/MSO/MDO3000 and DPO/MSO/MDO4000 Series oscilloscope?
The Measurements are the same as the DPO/MSO2000 Series scopes. By going into the measurement menu you can add and remove up to 4 measurements. You can gate the measurements which allows you to only measure the part of the captured waveform that you …
FAQ ID64651
Is Analog BW upgradable on the MDO4000C and can it be upgraded in the field?
Yes, the MDO4000C analog bandwidth has upgradable bandwidth options. Once purchased it does require a new calibration at Tektronix Service Center. 
FAQ ID72121
How do I run a Signal Path Compensation (SPC) on an DPO/MSO/MDO4000 Series oscilloscope?
Signal Path Compensation (SPC) should be run anytime you are getting DC offsets in your signals, or your scope has moved locations and might have changed temperature, or if it's been more then a month since your last SPC. This is a standard procedure …
FAQ ID64681
How do I set up a I2C Bus Decode?
The procedure to set up a I2C bus decode and trigger is simple once you understand the basics. First you have to have the correct module or scope option. Second make sure your signal is on screen and taking up as much of the DAC as possible with good …
FAQ ID64756
What MDO4000C options can be upgraded in the field?
Only MSO, AFG & DVM/Frequency counter can be upgraded in the field. The DVM/Frequency counter is available on all models and is free when when the product is registered. Analog bandwidth upgrade options require the instrument to be calibrated at the …
FAQ ID72136
How can I change the TekVISA Instrument descriptor “device name” used to identify the oscilloscopes to which I routinely connect?
Open TekVISA V4.0.0+ OpenChoice Instrument Manager by selecting Start -> All Programs -> TekVISA ->  OpenChoice Instrument Manager.Select (highlight) the Instrument descriptor listed in the Instruments list for the connected Oscilloscope.Click the …
FAQ ID66181
How do I clear my memory using TekSecure on a MSO/DPO/MDO4000 Series oscilloscope?
This procedure for clearing the memory on oscilloscope can be applied to the DPO/MSO/MDO4000, DPO/MSO3000 and DPO/MSO2000 Series oscilloscope families. By clearing the memory you will lose all saved reference waveforms, saved setups and all other …
FAQ ID64686
How do I Set Up a LIN serial Bus decode?
For doing Local Interconnect Network (LIN) bus decode Tektronix recommends using a DPO/MSO/MDO series oscilloscope. This feature can be purchased as a module or option key on any of these types of oscilloscopes. Start by turning it on the bus channel …
FAQ ID64781
When customer upgrades bandwidth on a MDO4000C, will the warranty be 3 years from the date of bandwidth upgrade?
No, the warranty does not get reset with the purchase of a bandwidth upgrade or spectrum analyzer upgrade. However, the instrument is returned from the Tektronix Service Center fully calibrated. If you have further questions please connect with our …
FAQ ID72156
What probes are supported on the RF input of the MDO3000 and MDO4000 series?
The RF input on the MDO3000 and MDO4000 series has an N connector, so the RF input can support cables, antennas, and other adapters typically used with a spectrum analyzer.  The RF input is 50 ohms and it is AC coupled.  Below is a listing of some …
FAQ ID64506
What are some of the benefits of the TekVPI probe interface?
The biggest benefits of the TekVPI™ probe interface are versatility and ease of use. Oscilloscopes with TekVPI interface support a wide range of probes including TekVPI probes, BNC and TekProbe-BNC Level 1 probes, and TekProbe-BNC Level 2 probes …
FAQ ID56016
Will the P6516 Logic Probe work on my MSO4000B, MDO4000B and MDO4000C Series oscilloscopes?
The P6516 logic probe was only used with the original MSO4000 series. For the subsequent MSO4000B, MDO4000B and MDO4000C Series oscilloscopes, the P6516 was replaced by the P6616 logic probe. The P6616 logic probe will not work on the original …
FAQ ID246206
How do I save and load a reference waveform to a DPO/MSO3000 series oscilloscope?
This Video will explain how to setup, save and load a reference waveform. It can be done through a USB flash drive or by internal memory. This method for using reference waveforms can be applied to all MSO/DPO2000, MSO/DPO3000, MSO/DPO/MDO4000 …
FAQ ID64641
How do I set up a RS232 bus decode?
The procedure to set up a RS232 bus decode and trigger is simple once you understand the basics. First you need to have the correct module or scope option. Second make sure your signal is on screen and taking up as much of the screen as possible with …
FAQ ID64761
My company purchased a Tektronix MDO4104C oscilloscope last year and we purchased three application modules. They are not showing up on our scope anymore and we would like some help getting them back.
Push Utility on the front panel. If needed, push Utility Page on the lower menu and turn multipurpose knob a to select Config.  Push Manage Modules and Options on the lower menu, and then push License Type on the side menu until “Modules” is selected …
FAQ ID468031
How do I set up an Ethernet bus decode?
Make sure your setup is prepared to decode, that you have the needed probes, scope options, test boards, etc. Once you have the options it's important to know how to use the options and probe your signal. To setup Ethernet bus decoding, turn on your …
FAQ ID64731
What are the acquisition bands in the MDO4000, MDO4000B, and MDO4000C?
The acquisition bands are as follows: 1) 9kHz - 3.75 GHz (MDO4000B/C) or 50 kHz - 3.75 GHz (MDO4000)2) 2.75 GHz - 4.5 GHz3) 3.5 GHz - 6.0 GHzThese three bands overlap, allowing the MDO to have a 1 GHz capture bandwidth at all center frequencies and …
FAQ ID69341
How do I Set up a Military Standard 1553 serial bus decode?
For doing Military Standard 1553 bus decode Tektronix recommends using a DPO/MSO/MDO 2000 or higher series oscilloscope. This feature can be purchased as a module or option key on any of these types of oscilloscopes. Start by turning it on the bus …
FAQ ID64776
How do I erase and declassify an MSO/DPO2000, MSO/DPO/MDO3000, and MSO/DPO/MDO4000 Series oscilloscope?
This example will show you how to declassify the MDO4000/B/C Series oscilloscope. This procedure also applies to the MSO/DPO4000/B, MSO/DPO/MDO3000, and the MSO/DPO2000/B series of oscilloscope.The first step in the declassification process is …
FAQ ID66231
Why isn’t the TPP1000 (Tektronix Passive Probe 1GHz) compatible with my scope?
Short answer is that if your scope doesn’t have the notched key that allows the probe to connect, then the TPP probe requires a different termination resistance than what your scope can provide. Long answer is that traditionally, passive probes …
FAQ ID467701
Programing - How do I get a Screen Capture from DPO4000 scope using Python?
There are a few things that are needed for programming with an oscilloscope. First it's important to have a copy of your oscilloscopes Programmers manual. This can be found be searching for manuals on Tek.com and specifying Programmers manual in the …
FAQ ID64791
How do I utilize the XY display feature on a DPO/MSO/MDO4000 Series oscilloscope?
The XY display format can be used to measure the phase relationship between two or more synchronous signals. This measurement technique involves inputting one signal into the vertical system as usual and then another signal into the horizontal system …
FAQ ID64666
Can the MDO3000 capture the time domain and the frequency domain simultaneously?
The MDO3000 is most importantly an oscilloscope, but has a total of 6 different instruments individually built into it. Designed in such a way to minimize the clutter on your bench but give you the power and versatility you need. Unfortunately to be …
FAQ ID69306
The data sheet for my oscilloscope says that the vertical input sensitivity is 1 mV/div to 10 V/div in 1 MΩ mode. But I turn the Vertical Scale control fully clockwise and I can only get down to 10 mV/div. What am I doing wrong?
You probably aren't doing anything wrong. But you do have a 10X probe attached to that channel, right? The 1 mV/div specs relate to the oscilloscope inputs. If the signal’s source impedance is relatively low (<< 1 MOhm), the signal’s frequency is …
FAQ ID58571
Why Should My Signal Fit Within The Screen Of My Tektronix Oscilloscope?
Scaling your signal to fit within the screen will remove signal distortion caused by clipping. Clipping is caused by exceeding the limits of the instrument's input. Tektronix's digital oscilloscopes are designed such that each division is 25 digital …
FAQ ID60306
Which probes are compatible with oscilloscopes with the TekVPI probe interface?
There are a couple different types of TekVPI interfaces, one with a notch and one without. The notch was implemented later and was put in place because the front end was designed differently and communicates uniquely with those types of probes …
FAQ ID56226
Does Tektronix have a 12-bit oscilloscope?
Yes! Tektronix offers many different models of real-time oscilloscopes that provide 12-bit or greater vertical resolution for a variety of applications. Because many high-vertical-resolution oscilloscopes on the market have technical trade-offs such …
FAQ ID69266
How do I configure the LAN settings on an MDO4000C series oscilloscope?
This procedure also applies to the DPO/MSO/MDO4000B series oscilloscopes. As it stands now, all 4000 series scopes  require a live network connection  be made on the scope in order to set and save LAN settings. If the scope does not have a network …
FAQ ID66236
When should I use MagniVu on my oscilloscope?
MagniVu allows you to have higher resolution to accurately determine edge placement on your digital data. It helps you to make precise timing measurements on digital edges. On the MSO/MDO4000/B/C and MSO5000/B Series, you can see up to 32 times more …
FAQ ID63886
Can the P6316, P6516, or P6616 logic probes be used interchangeably?
The simple answer is no they can't be used interchangeably. The front end of the logic channels are different so different logic probes are needed between the scopes.   For MSO2000/B, MSO3000, and MDO3000 Series oscilloscopes, only the P6316 logic …
FAQ ID59166
Do the existing MSO/DPO/MDO4000/B Series application modules work with the MDO4000C?
Yes, almost all work from all legacy MSO/DPO/MDO4000/B series scopes. The only one that has some requirements is the MDO4TRIG which requires a spectrum analyzer option MDO4SA3 or MDO4SA6 be installed on your MDO4000C before RF triggering capabilities …
FAQ ID72146
I could not find any information regarding the increase in bits in resolution for HiRes mode. Is there any information available?
The increase in bits in resolution depends on the decimation ratio.  The decimation ratio can be determined as follows:D = MFs / FsMFs is the maximum non-interleaved sampling frequency of the scope.  For example: 5 GS/s for the DPO4104B or 2.5 GS/s …
FAQ ID55421
What's included in the MDO3000 and MDO4000C DDU option? 
The Distribution Demo Unit (DDU) option on Tektronix oscilloscopes is an option provided to distributors for demoing scopes to customers with a set time limit before it expires. Questions arise about what's included in the MDO3000 and MDO4000C Series …
FAQ ID72196
Do we get a Spectrum Analyzer equal to the analog bandwidth with a purchase of the MDO4000C?
No, all MDO4000C come without Spectrum Analyzer (SA) options. For flexibility you can now order the base unit and add either option MDO4SA3 (3GHz RF channel) or MDO4SA6 (6GHz RF channel). When MDO4SA3 or MDO4SA6 is NOT ordered, the oscilloscope comes …
FAQ ID72131
I downloaded and Installed OpenChoice Desktop, but it doesn't recognize my scope.
Refer to the Prerequisites.txt file available to download on the same page for OpenChoice desktop. Make sure you have all the prerequisites specified.    Prerequisites 1. PC equipped with  Microsoft Windows 7 32 Bit and 64 Bit OS, Windows 8.1 32 Bit …
FAQ ID474266
How do I set up a CAN bus decode?
Depending on what scope you have will depend on what options are availiable for decoding your CAN signal. For all the DPO/MSO2000/3000/4000/5000 and MDO3000/4000 Series scopes there are modules or license keys that can be purchased. Once you have one …
FAQ ID64751
How Do I Set Up a Parallel Bus Decode?
For doing Parallel Bus decode Tektronix recommends using a MSO or MDO + MSO option Series oscilloscopes. This feature comes standard in the Bus menu and can be used in a variety of ways. Start by turning it on, selecting the channel and setting your …
FAQ ID64771
Companies such as National Instruments and LeCroy sell USB-to-GPIB adapters. How do their adapters compare to the TEK-USB-488?
The products from National Instruments (GPIB-USB-B or GPIB-USB-HS) and LeCroy (WS-GPIB) are USB host to GPIB device adapter. These would be used for instruments that have a GPIB interface with controllers that have a USB port. The TEK-USB-488 was …
FAQ ID56456
Can my oscilloscope operate on 400Hz power?
Most scopes have a wide range of operating voltages and frequencies, a full list can be found in the user manual of your specific oscilloscope. If you're having trouble finding your answer or can't find the manual, please call our Technical Support …
FAQ ID63266
Programing - How to get and plot a waveform from DPO/MSO/MDO4000 Series scope in Python
There are a few things that are needed for programming with an oscilloscope. First it's important to have a copy of your oscilloscopes Programmers manual. This can be found be searching for manuals on Tek.com and specifying Programmers manual in the …
FAQ ID64796
MDO4000 Series vs. Regular Oscilloscope FFTs
Examine the MDO4000 Series vs a regular oscilloscope FFTs.

참고자료 번호: 48W-28711-0
경쟁사
MDO4000 Series Mixed Domain Oscilloscopes (Replaced by MDO4000B)
Replaced by the MDO4000B -- Introducing the world’s first and only oscilloscope with a built-in spectrum analyzer. For the first time ever, you can capture time-correlated analog, digital, and RF signals for a complete system view of your device. See …

참고자료 번호: 48W-26875-4
Datasheet
MDO4000C Series
Mixed Domain Oscilloscope

This manual provides detailed specifications and procedures to verify guaranteed specs for the instrument supported by this manual.


부품 번호: 077117801
성능 확인
MDO4000C, MDO4000B, MDO4000, MSO4000B, DPO4000B, and MDO3000 Series
Digital Oscilloscopes

This manual explains the use of commands for remotely controlling youroscilloscope. With this information, you can write computer programs toperform functions, such as setting the front-panel controls, taking measurements, performing statistical calculations, and exporting data for use in other programs.


부품 번호: 077051009
프로그래머
MDO4000C Series
Oscilloscope Service Manual

This manual provides customer service procedures for the MDO4000C series oscilloscope.
부품 번호: 077117900
서비스
MDO4000C, MDO4000B, MDO4000, MSO4000B, DPO4000B, and MDO3000 Series
Digital Oscilloscopes

This manual explains the use of commands for remotely controlling youroscilloscope. With this information, you can write computer programs toperform functions, such as setting the front-panel controls, taking measurements, performing statistical calculations, and exporting data for use in other programs.


부품 번호: 077051007
프로그래머
MDO4000C Series
Oscilloscope User Manual

This user manual provides detailed information about the safe and effective operation of the MDO4000C series oscilloscopes.
부품 번호: 077116700
주 사용자
MDO4000C Series Oscilloscope
Security and Declassification Instructions

This document describes memory erasure and sanitization procedures for the MDO4000C Series Oscilloscopes.
부품 번호: 077118000
기밀 해제
KickStart Instrument Control Software Version 2.2.0 (Windows 10, 8, 7 compatible)
"KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the …

부품 번호: KICKSTART-2.2.0
애플리케이션
ARBEXPRESS WAVEFORM CREATION AND EDITING SW, V3.5
ArbExpress is a waveform creation and editing tool for Tektronix AWG and AFG instruments. It provides an easy to use and efficient way to create and edit waveforms, transfer waveforms to and from Arbitrary Waveform Generators (AWG), and …

부품 번호: 066146105
애플리케이션
KickStart Instrument Control Software Version 2.1.1 (Windows 10, 8, 7 compatible)
"KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the …

부품 번호: KICKSTART-2.1.1
애플리케이션
TEKVISA Connectivity Software - V4.2.0
TekVISA is the Tektronix implementation of VISA (Virtual Instrument Software Architecture), an industry-standard communication protocol.When installed on a PC, TekVISA provides communication with instruments that are connected to the PC via various …

부품 번호: 066093812
드라이버
DPO2000, MSO2000, DPO3000 and DPO4000, MSO3000 and MSO4000, MDO3000 and MDO4000 and MDO3 IVI Driver - V1.5
The Tektronix MSO/DPO2000, MDO/MSO/DPO3000, MDO/MSO/DPO4000 and MDO3 IVI Driver is an IVI class-compliant driver. It complies with Scope Class specifications (IVI-4.1) as defined by the IVI foundation. An IVI class-compliant specific driver for an …

부품 번호: 066133104
드라이버
SignalVu-PC Vector Signal Analysis Software - V3.23.0022
SignalVu-PC VSA software brings the analysis engine of the Tektronix Real-Time Signal Analyzer (RTSA) to your computer, enabling you to analyze live signals from RSA306, RSA500, RSA600, RSA7100A Spectrum Analyzers and MDO4000B/C Series oscilloscopes …

부품 번호: 066143422
애플리케이션
KickStart Instrument Control Software Version 2.1.0 (Windows 10, 8, 7 compatible)
"KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the …

부품 번호: KICKSTART-2.1.0
애플리케이션
SignalVu-PC Vector Signal Analysis Software - Release Candidate - V3.17.0013
SignalVu-PC VSA software brings the analysis engine of the Tektronix Real-Time Signal Analyzer (RTSA) to your computer, enabling you to analyze live signals from RSA306, RSA500, RSA600, RSA7100A Spectrum Analyzers and MDO4000B/C Series oscilloscopes …

부품 번호: 066143420
애플리케이션
SignalVu-PC Vector Signal Analysis Software - V3.16.0014
SignalVu-PC VSA software brings the analysis engine of the Tektronix Real-Time Signal Analyzer (RTSA) to your computer, enabling you to analyze live signals from RSA306, RSA500, RSA600, RSA7100A Spectrum Analyzers and MDO4000B/C Series oscilloscopes …

부품 번호: 066143419
애플리케이션
MDO4KC FIRMWARE RELEASE - v1.10
MDO4kC firmware update

부품 번호: 066179905
펌웨어
TEKVISA CONNECTIVITY SOFTWARE - V4.1.1
TekVISA is the Tektronix implementation of VISA (Virtual Instrument Software Architecture), an industry-standard communication protocol.When installed on a PC, TekVISA provides communication with instruments that are connected to the PC via various …

부품 번호: 066093811
드라이버
MDO4000C FIRMWARE V1.04
This firmware is for all MDO4000C Series oscilloscopes.

부품 번호: 066179902
펌웨어
Tektronix Openchoice Desktop Application TDSPCS1 - v2.6
The Tektronix OpenChoice Desktop free application lets you capture oscilloscope screen images, waveform data, and settings from a Microsoft Windows computer. After installing the software, refer to the section “Connecting to a PC” in your …

부품 번호: 066093914
유틸리티
ARBEXPRESS WAVEFORM CREATION AND EDITING SW, V3.4
ArbExpress is a waveform creation and editing tool for Tektronix AWG and AFG instruments. It provides an easy to use and efficient way to create and edit waveforms, transfer waveforms to and from Arbitrary Waveform Generators (AWG), and …

부품 번호: 066146104
애플리케이션
MDO How it Works
Look inside a Mixed Domain Oscilloscope to see how it acheives its spectrum analyzer performance, including high dynamic range and exceptionally high capture bandwidth with dedicated hardware and algorithms.

참고자료 번호: 48W-60187-2
기술 요약
MDO4000C and MDO3000 Series Comparison Fact Sheet
This fact sheet compares features and specifications of MDO4000C and MDO3000 Series mixed domain oscillscopes.

참고자료 번호: 48W-30086-2
선택 가이드
4 Series MSO vs MDO4000C
This fact sheet compares important specifications and features of the Tektronix 4 Series MSO Mixed Signal Oscilloscope to those of the Tektronix MDO4000 Series Oscilloscopes.

참고자료 번호: 48W-61606-0
팩트 시트
SOLUTIONS FOR SCIENTIFIC AND ENGINEERING RESEARCH

참고자료 번호: 55W_30503_2
브로슈어
Accurate Measurements Matter
MDO4000C Series measurements are taken on actual acquisition data - providing as much data to the measurement algorithms as possible. The Keysight 4000 X-Series uses the lower resolution display data, which can produce measurements that are …

참고자료 번호: 55W-61055-0
팩트 시트
Automotive Solutions Brochure
The pace of change in automotive electronics has never been faster, resulting in safer, more efficient, and more connected vehicles. Technologies such as high-speed data communications, wireless communications, radar, and power supplies underpin …

참고자료 번호: 45W-60646_1
브로슈어
Power Supply Measurement & Analysis with Bench Oscilloscopes
Today’s power supplies are driving to a level of efficiency never seen before, requiring design engineers to perform specialized power measurements that are time-consuming and complex. Learn how using a Tektronix Bench Oscilloscopes provides fast …

참고자료 번호: 3GZ-23612-6
애플리케이션 노트
Power Supply Measurement and Analysis Primer
A power supply is a component, subsystem, or system that converts electrical power from one form to another; commonly from alternating current (AC) utility power to direct current (DC) power. The proper operation of electronic devices ranging from …

참고자료 번호: 55T-18412-6
입문서
Practical EMI Troubleshooting
After failing an EMI compliance test, where do you start? This application note gives guidance on connecting the information in your test report to a source of radiated emissions.  It provides information that applies to any spectrum analyzer -- such …

참고자료 번호: 3GW-30828-2
애플리케이션 노트
Testing a New Switch Mode Power Supply Design Poster
Get a quick overview of the key measurements for verifying a new switch mode power supply (SMPS) design.  This poster shows key measurements, from verifying your prototype during initial startup, to optimizing switching loss and magnetic losses, to …

참고자료 번호: 46W-60156-0
포스터
Fundamentals of the MDO4000 Series Mixed Domain Oscilloscope
Today’s design engineers often must debug complex devices, with integrated analog and digital signals, serial buses, and now RF signals for wireless communication. In this application note, learn how a Mixed Domain Oscilloscope (MDO) offers time …

참고자료 번호: 48T-26923-1
애플리케이션 노트
Keysight 4000X vs MDO4000C Competitive Comparison
Side-by-side comparison on important features like serial triggering and decode, waveform navigation and search, waveform capture rate, digital debug with MSO, and more.

참고자료 번호: 3GW-29111-3
경쟁사
Oscilloscope Selection Guide
From basic signal-checking to high-performance analysis, this selection guide gives an overview of the complete range of oscilloscopes from Tektronix. Comparison tables give high-level specifications and features, and indicate the major differences …

참고자료 번호: 46W-31080-7
선택 가이드
Identifying Setup and Hold Violations with a Mixed Signal Oscilloscope
Problems with setup and hold timing are among the most challenging to identify.  Mixed signal oscilloscopes (MSOs) are able to capture both analog and digital representations of signals, making them well-suited for identifying digital timing problems …

참고자료 번호: 55W-61095-0
애플리케이션 노트
How to Minimize Probe Loading with Low Capacitance Probes
Probing a circuit always has some impact on signals. Probe loading changes the signal being probed and can cause measurement problems or can even cause a circuit to perform differently. Reducing capacitive loading can help minimize these effects. In …

참고자료 번호: 51W-26294-6
애플리케이션 노트
Tektronix MDO4000C Series Oscilloscopes
This demonstration guide takes you through a series of step-by-step demonstrations on how the MDO4000C Series oscilloscope helps simplify the debug of mixed signal designs with its powerful functionality and integrated test instruments. This …

참고자료 번호: 48W-60217-0
사용 방법 가이드
MDO Signal Path Teardown Poster
MDO4000 and MDO3000 Mixed Domain Oscilloscopes deliver uncompromised oscilloscope performance combined with spectrum analyzer performance on par with standalone spectrum analyzers. But how do they do it? The answer lies in Tektronix’ custom ASICs, a …

참고자료 번호: 48W-60186-2
포스터
Serial Support Using Tektronix Oscilloscopes and Optional Software
Tektronix oscilloscopes offer a portfolio of optional analysis capabilities to simplify serial bus debug or compliance verification. This selection matrix shows which serial standards are supported by each of the oscilloscope series.  

참고자료 번호: 55W-29028-13
선택 가이드
Replicating Real World Signals with an Arbitrary/Function Generator
Learn how to simulate sensor and bus signals on an arbitrary waveform generator.  Find out how to capture signals using an oscilloscope, edit them using PC software, and play them back on an arbitrary/function generator.

참고자료 번호: 76W-18661-2
애플리케이션 노트
Advanced Radar Analysis: Tools for Measuring Modern Radar Application Note
With today's rapid advances in radar technology, developing and manufacturing highly specialized and innovative electronic products to detect radar signals takes leading-edge technology and tools. Tektronix innovative test equipment reduces …

참고자료 번호: 37W-23378-4
애플리케이션 노트
Capacitance and Inductance Measurements Using an Oscilloscope and a Function Generator
If you don't have an LCR meter in your lab, or you want to demonstrate the behavior of capacitors and inductors under sinusoidal stimulus, an oscilloscope and a function generator can help you to do a simple, transparent impedance measurement. You …

참고자료 번호: 75W-28152-0
애플리케이션 노트
MDO4000B Series vs. Rohde & Schwarz FSL Spectrum Analyzer
Examine the MDO4000 Series vs. the Rohde & Schwarz FSL Spectrum Analyzer

참고자료 번호: 48W-29951-0
경쟁사
MDO4000B Series vs. Rohde & Schwarz FSV Spectrum Analyzer
Examine the MDO4000 Series vs. the Rohde & Schwarz FSV Spectrum Analyzer

참고자료 번호: 48W-29952-0
경쟁사
MDO4000B Series vs. Rohde & Schwarz FSC Spectrum Analyzer
Examine the MDO4000 Series vs. the Rohde & Schwarz FSC Spectrum Analyzer

참고자료 번호: 48W-29950-0
경쟁사
장비 최대한활용하기
텍트로닉스 오실로스코프 소프트웨어,프로브 및 악세사리를 사용하면 오실로스코프를 특정 애플리케이션 요구사항 및 환경에 맞출 수 있습니다.

참고자료 번호: 60W_14232_10
제품 선택 가이드
Wave Inspector® 탐색 및 검색: 파형 분석이 간편해집니다.
무어의 법칙에 따라 전자 기술이 더욱 빠르게 발전하면서, 시스템 설계는 점점 복잡해지고 이에 따라설계, 구축, 문제해결 및 고장 시 수리도 어려워지고 있습니다. 그러면 이것이 최신 오실로스코프에는 어떤 의미를 주는 걸까요?

참고자료 번호: 48T-19039-9
애플리케이션 노트
The Secrets Behind the MDO4000 Series Spectrum Analyzer
Learn how: The MDO4000 Series are able to leverage oscilloscope acquisition technology to achieve spectral fidelity on par with entry level spectrum analyzers. The design techniques used in the MDO4000 Series allow them to achieve spectral fidelity …

참고자료 번호: 48W-28882-2
백서
Introduction to Video Measurements
In this application note, we demonstrate using a MSO/DPO5000, MDO/MSO/DPO4000 and MDO/MSO/DPO3000 Series Oscilloscope to make a variety of video measurements that are common in standard and high definition systems.

참고자료 번호: 3GW-20975-2
애플리케이션 노트
MDO4000B Series vs. Agilent N9322C
Side-by-side comparison on important specifications and features like correlating RF to other system signals and exceptionally wide capture bandwidth.

참고자료 번호: 48W-29948-0
경쟁사
MDO4000B Series vs. Agilent N9320
Side-by-side comparison on important specifications and features like correlating RF to other system signals and exceptionally wide capture bandwidth.

참고자료 번호: 48W-29949-0
경쟁사
MDO4000B Series vs. Agilent N9000A CXA
Side-by-side comparison on important specifications and features like correlating RF to other system signals and exceptionally wide capture bandwidth.

참고자료 번호: 48W-29946-0
경쟁사
임베디드 시스템 설계의 저속 직렬 버스 디버깅
일반적인 임베디드 시스템은 켜지자마자 특수 목적을 지닌 애플리케이션을 실행하며 시작 하고 꺼질 때까지는 작동이 멈추지 않습니다. 사실상, 오늘날 설계되고 생산되는 모든 전자 장치는 임베디드 시스 템입니다. 임베디드 시스템의 예로는 다음과 같은 것이 있습니다.

참고자료 번호: 48W-19040-21
애플리케이션 노트
MDO4000C Series
Oscilloscope

MDO4000C 혼합 도메인 오실로스코프에는 내장 장비가 최대 6 대 포함되며, 각 장비는 까다로운 문제를 해결 할 수 있는 뛰어난 성능을 제공합니다. 모든 오실로스코프는 강력한 트리거링, 검색 및 분석 기능을 갖추고 있으며 동기화된 아날로그, 디지털 및 RF 신호 분석을 제공하는 유일한 장비입니다. MDO4000C 는 완전한 사 용자 지정 가능하며 모든 부분을 업그레이드할 수 있습니다.


부품 번호: 077117602
사용자
MDO4000C Series
Oscilloscope User Manual

MDO4000C 혼합 도메인 오실로스코프에는 내장 장비가 최대 6 대 포함되며, 각 장비는 까다로운 문제를 해결 할 수 있는 뛰어난 성능을 제공합니다. 모든 오실로스코프는 강력한 트리거링, 검색 및 분석 기능을 갖추고 있으며 동기화된 아날로그, 디지털 및 RF 신호 분석을 제공하는 유일한 장비입니다. MDO4000C 는 완전한 사 용자 지정 가능하며 모든 부분을 업그레이드할 수 있습니다.
부품 번호: 077117601
주 사용자
MDO4000C Series
Oscilloscope User Manual

MDO4000C 혼합 도메인 오실로스코프에는 내장 장비가 최대 6 대 포함되며, 각 장비는 까다로운 문제를 해결 할 수 있는 뛰어난 성능을 제공합니다. 모든 오실로스코프는 강력한 트리거링, 검색 및 분석 기능을 갖추고 있으며 동기화된 아날로그, 디지털 및 RF 신호 분석을 제공하는 유일한 장비입니다. MDO4000C 는 완전한 사 용자 지정 가능하며 모든 부분을 업그레이드할 수 있습니다.
부품 번호: 077117600
사용자