다운로드
다운로드

매뉴얼, 데이터 시트, 소프트웨어 등을 다운로드할 수 있습니다.

다운로드 유형
모델 또는 키워드

MDO3000

MDO3000 혼합 도메인 오실로스코프에는 스펙트럼 분석기, 함수 발생기 등 최대 6대의 장비가 통합되었습니다. 이 스코프 하나로 아날로그, 디지털, RF 신호를 모두 캡처할 수 있습니다. 설계가 변경되는 경우 장비와 분석 기능, 업그레이드 대역폭을 추가할 수 있습니다.

Bandwidth

최대 1GHz

Record length

10M 포인트

Analog channels

2 또는 4

Sample Rate

최대 5GS/s

 

강력한 스코프는 시작에 불과합니다.

Thumbnail

오늘날의 엔지니어링 분야는 다중 코어 프로세서, 시리얼 버스 및 무선 인터페이스가 지배합니다. MDO3000의 중심에는 기본 스펙트럼 분석기 및 디지털 전압계와 함께 제공되는 믿을 수 있는 텍트로닉스 오실로스코프가 있습니다. 해당 기능을 테스트 목적에 맞게 사용자 정의할 수 있습니다. 16가지 로직 채널, 50MHz 임의/함수 발생기, 프로토콜 분석 및 확장된 3GHz 스펙트럼 분석기를 추가하여 오늘날과 미래의 복합 디자인 구현을 지원합니다.

주요 특징

  • 125가지 트리거 조합을 제공하는 수상 경력의 오실로스코프
  • Wave Inspector® 컨트롤을 포함하는 10M 포인트 레코드 길이
  • 기본 스펙트럼 분석기 포함
  • 변화하는 테스트 요구에 맞게 장비 및 기능 추가

정확한 측정

Thumbnail

간단히 말해서, MDO3000 시리즈 스코프는 업계에서 가장 정확한 측정을 제공하도록 디자인되었습니다. 많은 다른 장비들이 저해상도 디스플레이 데이터만 제공하지만 MDO3000은 실제 획득 데이터를 측정합니다. 이러한 점을 고려해서 탁월한 디자인으로 구현되었습니다. 실제로 MDO3000을 사용하면 보장된 사양을 통해 안심하고 정확한 측정 결과를 얻을 수 있을 것입니다. 결과적으로 측정 정밀도는 디자인 무결성에도 영향을 줍니다. 정확도가 충족되지 않는다면 고려할 필요가 없을 것입니다.

최고의 가격, 즉 무료로 최선의 프로브 기능 사용 가능

Thumbnail

프로브는 측정 신호 경로의 핵심 요소입니다. MDO3000을 구입하시면 업계 최고의 프로브를 무료로 얻게 되는 셈입니다. 업계 최고 수준의 3.9pF 로드와 오실로스코프에 적합한 광대역을 자랑하는 TPP 시리즈 프로브는 여러분이 원하던 일상에서 사용하기 좋은 프로브입니다.

주요 특징

  • 아날로그 채널당 1개의 표준 TPP 시리즈 프로브 포함
  • 업계 최고의 낮은 프로브 부하 3.9pF 유지
  • 스코프 대역폭에 맞게 250MHz, 500MHz 또는 1GHz 프로브 대역폭 제공

RF 전문가처럼 무선 측정 구현 – 하나로 통합될 필요는 없음

Thumbnail

무선 통신과 EMI 문제 때문에 고민하고 계십니까? 아니면 시간 및 주파수 도메인 측정을 동시에 해야 하는 오실로스코프가 필요한 RF 전문가이십니까? 어떤 경우든 업무에 맞게 스펙트럼 분석기가 내장된 MDO3000 오실로스코프를 사용할 수 있습니다. FFT “스펙트럼 분석”을 제공하는 다른 오실로스코프와 달리, 진정한 스펙트럼 분석기가 내장되어 있어서 스코프의 편리함을 그대로 활용하면서 최대 3GHz에 이르는 RF 측정을 수행할 수 있는 제품은 MDO3000이 유일합니다.

주요 특징

  • 기본 스펙트럼 분석기(표준 포함)
  • 3GHz 스펙트럼 분석기 업그레이드 사용 가능
  • 업계에서 유일한 진정한 통합형 스펙트럼 분석기 하드웨어

Accidents happen. Make sure you're protected.

텍트로닉스는 잦은 장비 고장과 손상을 보장할 수 있도록 업계 최초의 장비 보호 플랜을 제공합니다. 이 보장 플랜에는 화면 손상, 얼룩, 깨진 마운트, 정전기 방전 또는 전자 장치의 과입력 사고 등이 포함됩니다. 텍트로닉스의 토털 보호 플랜(Total Protection Plan)으로 수리 또는 교체 비용을 줄여 보십시오. 자세한 사항은 비디오를 시청하거나 아래를 클릭하여 확인하십시오.

자세히 보기

모델 아날로그 대역폭 샘플링 속도 레코드 길이 아날로그 채널 디지털 채널 스펙트럼 분석기 함수 발생기 출력 정가
MDO3012 100MHz 2.5GS/s 10M 포인트 2 16(옵션) 최대 3GHz

1(옵션)

US $3,770
구성 및 견적
MDO3014 100MHz 2.5GS/s 10M 포인트 4 16(옵션) 최대 3GHz

1(옵션)

US $4,490
구성 및 견적
MDO3022 200MHz 2.5GS/s 10M 포인트 2 16(옵션) 최대 3GHz

1(옵션)

US $4,500
구성 및 견적
MDO3024 200MHz 2.5GS/s 10M 포인트 4 16(옵션) 최대 3GHz

1(옵션)

US $5,020
구성 및 견적
MDO3032 350MHz 2.5GS/s 10M 포인트 2 16(옵션) 최대 3GHz

1(옵션)

US $7,770
구성 및 견적
MDO3034 350MHz 2.5GS/s 10M 포인트 4 16(옵션) 최대 3GHz

1(옵션)

US $9,340
구성 및 견적
MDO3052 500MHz 2.5GS/s 10M 포인트 2 16(옵션) 최대 3GHz

1(옵션)

US $9,860
구성 및 견적
MDO3102 1GHz 5GS/s 10M 포인트 2 16(옵션) 최대 3GHz

1(옵션)

US $11,700
구성 및 견적
MDO3054 500MHz 2.5GS/s 10M 포인트 4 16(옵션) 최대 3GHz

1(옵션)

US $12,600
구성 및 견적
MDO3104 1GHz 5GS/s 10M 포인트 4 16(옵션) 최대 3GHz

1(옵션)

US $15,600
구성 및 견적
모델 아날로그 대역폭 샘플링 속도 레코드 길이 아날로그 채널 디지털 채널 스펙트럼 분석기 함수 발생기 출력 정가
MDO3012 100MHz 2.5GS/s 10M 포인트 2 16(옵션) 최대 3GHz

1(옵션)

US $3,770
구성 및 견적
MDO3014 100MHz 2.5GS/s 10M 포인트 4 16(옵션) 최대 3GHz

1(옵션)

US $4,490
구성 및 견적
MDO3022 200MHz 2.5GS/s 10M 포인트 2 16(옵션) 최대 3GHz

1(옵션)

US $4,500
구성 및 견적
MDO3024 200MHz 2.5GS/s 10M 포인트 4 16(옵션) 최대 3GHz

1(옵션)

US $5,020
구성 및 견적
MDO3032 350MHz 2.5GS/s 10M 포인트 2 16(옵션) 최대 3GHz

1(옵션)

US $7,770
구성 및 견적
MDO3034 350MHz 2.5GS/s 10M 포인트 4 16(옵션) 최대 3GHz

1(옵션)

US $9,340
구성 및 견적
MDO3052 500MHz 2.5GS/s 10M 포인트 2 16(옵션) 최대 3GHz

1(옵션)

US $9,860
구성 및 견적
MDO3102 1GHz 5GS/s 10M 포인트 2 16(옵션) 최대 3GHz

1(옵션)

US $11,700
구성 및 견적
MDO3054 500MHz 2.5GS/s 10M 포인트 4 16(옵션) 최대 3GHz

1(옵션)

US $12,600
구성 및 견적
MDO3104 1GHz 5GS/s 10M 포인트 4 16(옵션) 최대 3GHz

1(옵션)

US $15,600
구성 및 견적
  Tektronix
MDO3000
Tektronix
MDO4000C
Keysight
3000T
LeCroy
WaveSurfer 3000
R&S
RTM2000
Bandwidth 100MHz - 1GHz 200MHz - 1GHz 100MHz - 1GHz 200MHz - 750MHz 200MHz - 1GHz
Upgradeable Bandwidth
아날로그 채널 2 또는 4 4 2 또는 4 2 또는 4 2 또는 4
아날로그 샘플링 속도 최대 5GS/s 최대 5GS/s 최대 5GS/s 최대 4GS/s 최대 5GS/s
표준 레코드 길이(모든 채널) 10M 20M 2M 10M 10M
통합 임의/함수 발생기 50MHz(옵션) 50MHz(옵션) 20MHz(옵션) 25MHz(옵션) --
통합 로직 채널(MSO) 16개(옵션) 16개(옵션) 16개(옵션) 16개(옵션) 16개(옵션)
통합형 하드웨어 스펙트럼 분석기 최대 3GHz(옵션) 최대 6GHz(옵션) -- -- --
아날로그, 디지털 및 RF의 전체 동기화 -- -- -- --
표준 프로브 최대 1GHz 패시브 최대 1GHz 패시브 최대 500MHz 패시브 최대 500MHz 패시브 최대 500MHz 패시브
기본 보증 3년 3년 3년 3년 3년

임베디드 시리얼 버스 트리거, 디코딩 및 분석

Thumbnail

시리얼 버스에서 단일 신호에 주소, 컨트롤, 데이터 및 클럭 정보가 포함되는 경우가 자주 있습니다. 그렇기 때문에 원하는 이벤트를 분리하기가 어렵습니다. MDO3000 시리즈의 시리얼 애플리케이션 모듈은 자동 트리거, 디코딩 및 검색 기능을 포함한, 시리얼 버스를 디버그하는 견고한 도구로 오실로스코프를 변환합니다.

주요 특징

  • I2C, SPI, RS-232/422/485/UART
  • CAN/CAN FD, LIN, FlexRay
  • I2S/LJ/RJ/TDM
  • MIL-STD-1553, USB

파워 측정 및 분석

Thumbnail

더 높은 에너지 효율성에 대한 필요성은 설계자와 테스트 장비 모두에 새로운 기준을 요구하고 있습니다. 대기 전력 제한, 더 증가한 스위칭 속도 및 신호 범위, 손실이 더 낮은 반도체 장치로 인해 테스트 상황이 새로운 극한 상황이 되는 경우가 많습니다. MDO3000은 새롭게 출현하는 이러한 요구 사항을 해결하는 전원 테스트 솔루션을 제공합니다.

주요 특징

  • 스위칭 장치에서 파워 손실 측정
  • 리플과 노이즈 측정 및 분석
  • 전력 반도체 장치 특성화
  • 활성 전력 계수 보정 회로 디버깅

전자파 간섭(EMI) 및 전자파 적합성(EMC)

Thumbnail

설계 EMI/EMC 테스트 수행 시 항상 실패 위험이 뒤따르기 마련이며, 이 경우 일정을 못 맞추거나 예산을 초과하게 될 수 있습니다. 스펙트럼 분석기가 내장되어 있는 MDO3000을 사용하면 실험실에서 사전 컴플라이언스 테스트를 수행하여 전체 EMI 컴플라이언스 테스트를 한 번에 통과할 가능성이 대폭 높아집니다.

자동차/버스 – CAN/CAN FD 트리거, 디코딩 및 분석

Thumbnail

오늘날 자동차의 기술 요건으로는 이전보다 더 정교하고 민감한 전자 구성 요소와 시스템을 들 수 있습니다. 총 6대의 장비가 하나로 통합된 텍트로닉스의 MDO3000은 이러한 고급 기술의 테스트 및 확인과 관련한 문제점을 해결하기 위해 개발되었습니다. 이제 하나의 장비로 다음 작업을 수행할 수 있습니다.

  • CAN FD, CAN, LIN 및 FlexRay 디버깅 및 확인
  • 하이브리드/전기차의 고전력 테스트
  • 차량 내 무선 시스템 확인
  • 새 구성 요소 평가(MEMS 센서, LED 드라이브, LED)

 

데이터 시트 소프트웨어 패키지/소프트웨어 옵션 설명 구성 및 견적 요청
액세서리 119414600
데이터 시트 설명
보기 데이터 시트 프로브 집합, RF 측정, 근거리 프로브 집합, 패시브, 휴대용
액세서리 119660900
데이터 시트 설명
보기 데이터 시트 안테나, 고무 피복, BNC 커넥터 포함, KD4 VHF, 조정되지 않음, 고무 뚜껑이 붙어 있음
액세서리 ACD3000
데이터 시트 설명
보기 데이터 시트 MDO3000 시리즈 오실로스코프용 소프트 휴대용 케이스
액세서리 HCTEK4321
데이터 시트 설명
보기 데이터 시트 하드 운반 케이스
액세서리 MDO3AFG
데이터 시트 설명
보기 데이터 시트 MDO3000 시리즈 오실로스코프에 (1) 채널 AFG 추가
액세서리 MDO3MSO
데이터 시트 설명
보기 데이터 시트 MDO3000 시리즈 오실로스코프에 P6316 로직 프로브가 있는 (16) 디지털 채널 추가
액세서리 MDO3SA
데이터 시트 설명
보기 데이터 시트 MDO3000 시리즈 오실로스코프에서 스펙트럼 분석기 입력 주파수를 3GHz로 늘림
액세서리 P6316
데이터 시트 설명
보기 데이터 시트 MSO 프로브, 16채널 범용 프로브
액세서리 RMD3000
데이터 시트 설명
보기 데이터 시트 랙 마운트 키트
액세서리 TEK-USB-488
데이터 시트 설명
USBTMC-USB488 호환 Tektronix 장비용 IEEE488(GPIB) 통신 어댑터에 USB 연결
액세서리 TPA-BNC
데이터 시트 설명
TekProbe-BNC에서 TekVPI로 연결하는 프로브 어댑터
액세서리 TPA-N-PRE
데이터 시트 설명
외부 프리앰프, TPA 커넥터, SMA 입력
액세서리 TPA-N-VPI
데이터 시트 설명
보기 데이터 시트 N형 커넥터로 프로브 어댑터와 TekVPI 연결
데이터 시트 액세서리 설명
119414600 프로브 집합, RF 측정, 근거리 프로브 집합, 패시브, 휴대용
119660900 안테나, 고무 피복, BNC 커넥터 포함, KD4 VHF, 조정되지 않음, 고무 뚜껑이 붙어 있음
ACD3000 MDO3000 시리즈 오실로스코프용 소프트 휴대용 케이스
HCTEK4321 하드 운반 케이스
MDO3AFG MDO3000 시리즈 오실로스코프에 (1) 채널 AFG 추가
MDO3MSO MDO3000 시리즈 오실로스코프에 P6316 로직 프로브가 있는 (16) 디지털 채널 추가
MDO3SA MDO3000 시리즈 오실로스코프에서 스펙트럼 분석기 입력 주파수를 3GHz로 늘림
P6316 MSO 프로브, 16채널 범용 프로브
RMD3000 랙 마운트 키트
보기 데이터 시트 TEK-USB-488 USBTMC-USB488 호환 Tektronix 장비용 IEEE488(GPIB) 통신 어댑터에 USB 연결
보기 데이터 시트 TPA-BNC TekProbe-BNC에서 TekVPI로 연결하는 프로브 어댑터
보기 데이터 시트 TPA-N-PRE 외부 프리앰프, TPA 커넥터, SMA 입력
TPA-N-VPI N형 커넥터로 프로브 어댑터와 TekVPI 연결
Perform Quick Measurements with the Integrated Digital Voltmeter.
1m 50s
Sometimes bad things happen to good scopes!  Ensure you've got it covered with a Total Product Protection plan from Tektronix, the only coverage plan available for test equipment with accident …
1m 2s
See a few everyday examples of engineering tasks you can do with this ultimate 6-in-1 integrated instrument.
6m 54s
Monitor More of Your Design with the Integrated Logic Analyzer.
2m 48s
Debug Your Serial Buses in Seconds with the Integrated Protocol Analyzer.
2m 58s
Find Elusive Signal Problems with the MDO3000 Mixed Domain Oscilloscope.
2m 39s
The MDO3000 Mixed Domain Oscilloscope features six integrated instruments, including a spectrum analyzer, function generator and more, giving you the ability to capture analog, digital and RF …
56s
Uncover Noise Sources and Debug Wireless with the Integrated Spectrum Analyzer.
3m
Generate a Wide Range of Signals with the Integrated Arbitrary/Function Generator.
2m 31s
In this short video, we demo the CAN FD bus decoding process on the flexible MDO3000 oscilloscope. 
4m 28s
Discover the exceptionally wide capture bandwidth of the integrated spectrum analyzer found in the MDO3000 Series Mixed Domain Oscilloscope.
3m 24s
KickStart Instrument Control Software Version 2.2.1 (Windows 10, 8, 7 compatible)
KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the ability to …

부품 번호: KICKSTART-2.2.1
애플리케이션
How to Use a Mixed Signal Oscilloscope to Test Digital Circuits
Learn how to set up a mixed signal oscilloscope and how use it in several applications including: triggering on pulse width violations, combining analog and digital waveforms to capture crosstalk, troubleshooting setup/hold violations, and checking …

참고자료 번호: 3GT-24008-4
애플리케이션 노트
Measurement Data Logging with TekBench Oscilloscope Control Software
This application note describes how to use TekBench™ Software and a Tektronix oscilloscope to perform measurement data logging for evaluating a design’s reliability in a room temperature environment, such as a project laboratory.

참고자료 번호: 61W-61442-0
애플리케이션 노트
How can I change the TekVISA Instrument descriptor “device name” used to identify the oscilloscopes to which I routinely connect?
Open TekVISA V4.0.0+ OpenChoice Instrument Manager by selecting Start -> All Programs -> TekVISA ->  OpenChoice Instrument Manager.Select (highlight) the Instrument descriptor listed in the Instruments list for the connected Oscilloscope.Click the …
FAQ ID66181
How do I clear my memory using TekSecure on a MSO/DPO/MDO4000 Series oscilloscope?
This procedure for clearing the memory on oscilloscope can be applied to the DPO/MSO/MDO4000, DPO/MSO3000 and DPO/MSO2000 Series oscilloscope families. By clearing the memory you will lose all saved reference waveforms, saved setups and all other …
FAQ ID64686
How do I Set Up a LIN serial Bus decode?
For doing Local Interconnect Network (LIN) bus decode Tektronix recommends using a DPO/MSO/MDO series oscilloscope. This feature can be purchased as a module or option key on any of these types of oscilloscopes. Start by turning it on the bus channel …
FAQ ID64781
What are the maximum power draw ratings for the MDO3000 TEKVPI probes?
The MDO3000 has a max power draw of 25 Watts. The download link below provides a PDF listing of wattage draw for different active probes and max limits of Tektronix scopes, this will help determine the connection options available for any scope you …
FAQ ID69301
How do I erase and declassify an MSO/DPO2000, MSO/DPO/MDO3000, and MSO/DPO/MDO4000 Series oscilloscope?
This example will show you how to declassify the MDO4000/B/C Series oscilloscope. This procedure also applies to the MSO/DPO4000/B, MSO/DPO/MDO3000, and the MSO/DPO2000/B series of oscilloscope.The first step in the declassification process is …
FAQ ID66231
Why isn’t the TPP1000 (Tektronix Passive Probe 1GHz) compatible with my scope?
Short answer is that if your scope doesn’t have the notched key that allows the probe to connect, then the TPP probe requires a different termination resistance than what your scope can provide. Long answer is that traditionally, passive probes …
FAQ ID467701
Programing - How do I get a Screen Capture from DPO4000 scope using Python?
There are a few things that are needed for programming with an oscilloscope. First it's important to have a copy of your oscilloscopes Programmers manual. This can be found be searching for manuals on Tek.com and specifying Programmers manual in the …
FAQ ID64791
My Tektronix oscilloscope uses the Linux operating system.  Where do I get a copy of the linux open source code as stated in the GNU Lesser General Public License notice?
For our Linux based instruments or programs licensed under the “GNU General Public License (GPL) or Lesser GNU General Public License (LGPL)” the complete corresponding sources are available. You can order a complete machine-readable copy of the …
FAQ ID64866
How do I utilize the XY display feature on a DPO/MSO/MDO4000 Series oscilloscope?
The XY display format can be used to measure the phase relationship between two or more synchronous signals. This measurement technique involves inputting one signal into the vertical system as usual and then another signal into the horizontal system …
FAQ ID64666
Can the MDO3000 capture the time domain and the frequency domain simultaneously?
The MDO3000 is most importantly an oscilloscope, but has a total of 6 different instruments individually built into it. Designed in such a way to minimize the clutter on your bench but give you the power and versatility you need. Unfortunately to be …
FAQ ID69306
What probes are supported on the RF input of the MDO3000 and MDO4000 series?
The RF input on the MDO3000 and MDO4000 series has an N connector, so the RF input can support cables, antennas, and other adapters typically used with a spectrum analyzer.  The RF input is 50 ohms and it is AC coupled.  Below is a listing of some …
FAQ ID64506
The data sheet for my oscilloscope says that the vertical input sensitivity is 1 mV/div to 10 V/div in 1 MΩ mode. But I turn the Vertical Scale control fully clockwise and I can only get down to 10 mV/div. What am I doing wrong?
You probably aren't doing anything wrong. But you do have a 10X probe attached to that channel, right? The 1 mV/div specs relate to the oscilloscope inputs. If the signal’s source impedance is relatively low (<< 1 MOhm), the signal’s frequency is …
FAQ ID58571
Why Should My Signal Fit Within The Screen Of My Tektronix Oscilloscope?
Scaling your signal to fit within the screen will remove signal distortion caused by clipping. Clipping is caused by exceeding the limits of the instrument's input. Tektronix's digital oscilloscopes are designed such that each division is 25 digital …
FAQ ID60306
I recently registered our Tektronix oscilloscope, updated the firmware and am currently trying to activate the free DVM & Frequency Counter.  I don’t see any software downloads for activating the DVM. Am I doing something wrong, or looking in the wrong spot?
After you have registered your oscilloscope on Tek.com, you should have received an email with instructions.  The email is sent to the address you used to login to tek.com.  If you haven't received the email after registration: Check your spam …
FAQ ID468046
What probe interface does my oscilloscope have?
Oscilloscope series Probe interface CSA7000/CSA7000B TekConnect DPO2000 TekVPI DPO3000 …
FAQ ID64251
How do I use the arbitrary function generator on the MDO3000?
Hello and welcome to Tektronix! Today I’m going to demonstrate the function generator capability on the MDO3000 mixed domain oscilloscope. The MDO3000 contains an integrated arbitrary function generator (or AFG) that can output predefined or user …
FAQ ID69276
Will the DVM work on the MDO3000 series scope with a probe?
Yes,  the DVM works through the analog inputs, therefor you can use standard probes. If you have more questions please contact one of our Technical Support Centers and an Application Engineer will quickly answer your questions. 
FAQ ID69331
Is the MDO3000 DVM the same as making an analog channel waveform measurement?
No, the MDO3000 uses a DVM IC that takes AC+DC RMS, DC and AC RMS measurements from signal on the respective channel inputs.
FAQ ID69371
How do I set up a USB bus decode?
First you must have the USB module or option key that enables USB decoding for your scope as well as proper probes. For help finding the right probe use our probe selector tool. When you go into the bus option you must select USB and then make sure …
FAQ ID64726
How do I utilize the measurement features on a DPO/MSO/MDO3000 and DPO/MSO/MDO4000 Series oscilloscope?
The Measurements are the same as the DPO/MSO2000 Series scopes. By going into the measurement menu you can add and remove up to 4 measurements. You can gate the measurements which allows you to only measure the part of the captured waveform that you …
FAQ ID64651
How do I set up a I2C Bus Decode?
The procedure to set up a I2C bus decode and trigger is simple once you understand the basics. First you have to have the correct module or scope option. Second make sure your signal is on screen and taking up as much of the DAC as possible with good …
FAQ ID64756
How do I use the spectrum analyzer function on the MDO3000?
Hello and welcome to Tektronix! Today I’m going to demonstrate the spectrum analyzer capability on the MDO3000 mixed domain oscilloscope. The MDO3000 contains a full-fledged spectrum analyzer with many useful features, including automatic markers, a …
FAQ ID69281
How do I Set up a Military Standard 1553 serial bus decode?
For doing Military Standard 1553 bus decode Tektronix recommends using a DPO/MSO/MDO 2000 or higher series oscilloscope. This feature can be purchased as a module or option key on any of these types of oscilloscopes. Start by turning it on the bus …
FAQ ID64776
When should I use MagniVu on my oscilloscope?
MagniVu allows you to have higher resolution to accurately determine edge placement on your digital data. It helps you to make precise timing measurements on digital edges. On the MSO/MDO4000/B/C and MSO5000/B Series, you can see up to 32 times more …
FAQ ID63886
Can the P6316, P6516, or P6616 logic probes be used interchangeably?
The simple answer is no they can't be used interchangeably. The front end of the logic channels are different so different logic probes are needed between the scopes.   For MSO2000/B, MSO3000, and MDO3000 Series oscilloscopes, only the P6316 logic …
FAQ ID59166
I could not find any information regarding the increase in bits in resolution for HiRes mode. Is there any information available?
The increase in bits in resolution depends on the decimation ratio.  The decimation ratio can be determined as follows:D = MFs / FsMFs is the maximum non-interleaved sampling frequency of the scope.  For example: 5 GS/s for the DPO4104B or 2.5 GS/s …
FAQ ID55421
What are some of the benefits of the TekVPI probe interface?
The biggest benefits of the TekVPI™ probe interface are versatility and ease of use. Oscilloscopes with TekVPI interface support a wide range of probes including TekVPI probes, BNC and TekProbe-BNC Level 1 probes, and TekProbe-BNC Level 2 probes …
FAQ ID56016
How do I set up a CAN bus decode?
Depending on what scope you have will depend on what options are availiable for decoding your CAN signal. For all the DPO/MSO2000/3000/4000/5000 and MDO3000/4000 Series scopes there are modules or license keys that can be purchased. Once you have one …
FAQ ID64751
Is the MDO3000 free video the same as the DPO3VID.
On our past MSO/DPO3000 Series products, we had an extended video analysis module.  Well, we have now made all that capability standard on the MDO3000. And the 500MHz models and below also have a native 75 Ohm input termination – the native …
FAQ ID781581
I downloaded and Installed OpenChoice Desktop, but it doesn't recognize my scope.
Refer to the Prerequisites.txt file available to download on the same page for OpenChoice desktop. Make sure you have all the prerequisites specified.    Prerequisites 1. PC equipped with  Microsoft Windows 7 32 Bit and 64 Bit OS, Windows 8.1 32 Bit …
FAQ ID474266
What is included in the Tektronix Near Field Probe kit (Tek p/n 119-4146-00) and what are they used for?
The Tektronix 119-4146-00 Near Field Probe Set is intended to serve as a versatile aid for diagnostic testing of radiated emissions over a broad range of frequencies from below 100 kHz to above 1GHz.  The probe set consist of three (3) magnetic field …
FAQ ID64501
Does Tektronix have a 12-bit oscilloscope?
Yes! Tektronix offers many different models of real-time oscilloscopes that provide 12-bit or greater vertical resolution for a variety of applications. Because many high-vertical-resolution oscilloscopes on the market have technical trade-offs such …
FAQ ID69266
Programing - How to get and plot a waveform from DPO/MSO/MDO4000 Series scope in Python
There are a few things that are needed for programming with an oscilloscope. First it's important to have a copy of your oscilloscopes Programmers manual. This can be found be searching for manuals on Tek.com and specifying Programmers manual in the …
FAQ ID64796
How do I use the DVM and frequency counter function on the MDO3000?
Hello and welcome to Tektronix! Today I’m going to demonstrate the digital voltmeter and frequency counter functionality of the MDO3000 series mixed domain oscilloscope. The DVM can use any of the 4 analog scope inputs to feed the signal into a free …
FAQ ID69286
Why does the Tkdpo2k3k4k_ReadWaveform() function in the Tkdpo2k3k4k IVI-C driver time out every time I call it when I am connected to the instrument via Ethernet? The function call works fine over USB, but over Ethernet it always times out.
The Tkdpo2k3k4k_ReadWaveform() function makes use of the Service Request Event in VISA so the scope can notify the driver when it has completed its acquisition and the waveform data is ready to be fetched as opposed to the driver polling the scope …
FAQ ID72221
How do I use the serial decoder function on the MDO3000?
Hello and welcome to Tektronix, today I’m going to demonstrate the serial decoder capabilities of the MDO3000 series mixed domain oscilloscope.The MDO3000 has the ability to decode bus data into binary, hexadecimal, decimal, or ASCII values depending …
FAQ ID69296
What's included in the MDO3000 and MDO4000C DDU option? 
The Distribution Demo Unit (DDU) option on Tektronix oscilloscopes is an option provided to distributors for demoing scopes to customers with a set time limit before it expires. Questions arise about what's included in the MDO3000 and MDO4000C Series …
FAQ ID72196
Which probes are compatible with oscilloscopes with the TekVPI probe interface?
There are a couple different types of TekVPI interfaces, one with a notch and one without. The notch was implemented later and was put in place because the front end was designed differently and communicates uniquely with those types of probes …
FAQ ID56226
How do I use the mixed signal analysis function of the MDO3000?
Hello and welcome to Tektronix! Today I’m going to demonstrate the mixed signal capabilities of the MDO3000 series mixed domain oscilloscope.Much like its MSO predecessor, the MDO3000 boasts a 16-channel logic analyzer in addition to its 4 analog …
FAQ ID69291
: Can the optional AFG in the MDO3000, MDO4000C and 5 Series MSO be set to sweep?
AFG in MDO3000, MDO4000C, and 5 Series MSO do not have sweep function. But a limited sweep may be created using the arbitrary function.   Example: Create a sweep from 100 KHz to 250 KHz. ArbExpress (free software on Tek.com) select Equation Editor …
FAQ ID474056
Can my oscilloscope operate on 400Hz power?
Most scopes have a wide range of operating voltages and frequencies, a full list can be found in the user manual of your specific oscilloscope. If you're having trouble finding your answer or can't find the manual, please call our Technical Support …
FAQ ID63266
How do I use the Channel Monitor feature on the MDO3000 logic analyzer?
See attached PDF, which has explanations with images. 
FAQ ID69391
Is there a mictor adapter for the P6616 (logic probe for MSO5000B, MSO4000B, and MDO4000C + MDO4MSO) or P6516 (logic probe for the MSO4000 Series) or the P6316 (logic probe for MSO2000, MSO3000, MDO3000 + MDO3MSO Series)?
A mictor adapter is available from our partner Nexus Technologies. Use the mictor adapter NEX-HD2HEADER http://www.nexustechnology.com/products/laAccessories/hd2header/  
FAQ ID59716
Why do I see 16 flat lines for the MSO digital logic inputs when the same signals are displayed properly on the analog channels and all channels are setup for valid trigger threshold levels?
A common mistake for some, we first recommend verifing that the front panel MSO digital probe is properly connected by squeezing the probe's side latch buttons to un-plug, remove the probe then re-insert the probe label side up into the front panel …
FAQ ID60251
How do I reduce noise on signals using an oscilloscope?
There are many methods to reduce many types of noise on a signal. Tektronix oscilloscopes can do this through bandwidth limiting the scope input, averaging your signal, changing the sampling method to hi-resolution mode, and more. This video …
FAQ ID64706
Is the SA (Spectrum Analyzer) in the MDO3000 field upgradable?
Yes, the MDO3SA is field upgradable by customers. Any instrument can upgrade the SA input frequency to 3GHz using this quick process in the field. After inserting the SA app module in the MDO3000 the SA is enabled .The SA app module can be removed …
FAQ ID69321
Is the AFG (Arbitrary Function Generator) in the MDO3000 field upgradable?
Yes, the MDO3AFG is field upgradable by customers. The MDO3AFG is a "single-use" application module. This application module can enable the AFG which is already present in the instrument. After inserting the AFG app module in the MDO3000 the AFG is …
FAQ ID69316
Can active probes with TekProbe interface (such as a P6205) be used on the DPO4000B or MSO4000B series scopes?
Yes. A TPA-BNC adaptor is required for people to connect legacy TekProbe interface probes to the new TekVPI interface. The adapter works on any TekVPI scopes inlcuding the MSO/DPO/MDO4000/B/C, MSO/DPO/MDO3000 MSO/DPO2000/B or MSO/DPO5000/B or …
FAQ ID60416
How can I increase the measurement accuracy using automated measurements vs cursors?
While Cursors are quick and easy at approximating measurements, using the automated measurements can give you a much better and accurate measurement results. Here are some techniques to be successful in making accurate measurements. Always use …
FAQ ID62606
How do I save and load a reference waveform to a DPO/MSO3000 series oscilloscope?
This Video will explain how to setup, save and load a reference waveform. It can be done through a USB flash drive or by internal memory. This method for using reference waveforms can be applied to all MSO/DPO2000, MSO/DPO3000, MSO/DPO/MDO4000 …
FAQ ID64641
How do I set up a RS232 bus decode?
The procedure to set up a RS232 bus decode and trigger is simple once you understand the basics. First you need to have the correct module or scope option. Second make sure your signal is on screen and taking up as much of the screen as possible with …
FAQ ID64761
My company purchased a Tektronix MDO4104C oscilloscope last year and we purchased three application modules. They are not showing up on our scope anymore and we would like some help getting them back.
Push Utility on the front panel. If needed, push Utility Page on the lower menu and turn multipurpose knob a to select Config.  Push Manage Modules and Options on the lower menu, and then push License Type on the side menu until “Modules” is selected …
FAQ ID468031
How do I run a Signal Path Compensation (SPC) on an DPO/MSO/MDO4000 Series oscilloscope?
Signal Path Compensation (SPC) should be run anytime you are getting DC offsets in your signals, or your scope has moved locations and might have changed temperature, or if it's been more then a month since your last SPC. This is a standard procedure …
FAQ ID64681
How do I set up an Ethernet bus decode?
Make sure your setup is prepared to decode, that you have the needed probes, scope options, test boards, etc. Once you have the options it's important to know how to use the options and probe your signal. To setup Ethernet bus decoding, turn on your …
FAQ ID64731
How Do I Set Up a Parallel Bus Decode?
For doing Parallel Bus decode Tektronix recommends using a MSO or MDO + MSO option Series oscilloscopes. This feature comes standard in the Bus menu and can be used in a variety of ways. Start by turning it on, selecting the channel and setting your …
FAQ ID64771
What is aliasing and how do I detect it and fix it on my oscilloscope?
Aliasing is basically a form of under sampling and what is displayed on the scopes is an indistinguishable waveform. The under sampled waveform is then contstructed to look like a slower frequency waveform or a flat line in the case of the sample …
FAQ ID64691
What is the maximum bit rate a decoded SPI bus can trigger on?
Different oscilloscopes have different triggering circuitry therefor the limits of what speeds can be achieved vary by scope. Please use the following table to easily look up your scope and determine your max SPI bus trigger level.  For more …
FAQ ID62256
I cannot see my signal on the Oscilloscope. What can I do?
You have many options to help diagnose this issue, below are a few suggestions to get started. If you find yourself needing more help, please connect with our Technical Support Center. You can get started by pressing the "Contact Us" button on the …
FAQ ID63686
Companies such as National Instruments and LeCroy sell USB-to-GPIB adapters. How do their adapters compare to the TEK-USB-488?
The products from National Instruments (GPIB-USB-B or GPIB-USB-HS) and LeCroy (WS-GPIB) are USB host to GPIB device adapter. These would be used for instruments that have a GPIB interface with controllers that have a USB port. The TEK-USB-488 was …
FAQ ID56456
How do I utilize the math channel feature on a DPO/MSO/MDO3000 or DPO/MSO/MDO4000 Series oscilloscope?
There are three main functionalities on the Math button on this scope. They range from Dual Waveform Math, FFT (Fast Fourier Transform), and Advance Math. These three functionalities have a range of abilities and are explained in this short YouTube …
FAQ ID64656
How do I mount a network drive on my MDO3000 or MDO4000C oscilloscope?
This procedure also applies to the DPO/MSO/MDO4000/4000B series oscilloscopes.  Note: This Mount a network drive will not work with a direct (peer-to-peer) connection. Must go through your local DNS server. To begin, press the “Menu” button in the …
FAQ ID66201
How do I connect an SMA male output to Oscilloscopes with TekVPI BNC inputs?
Use a Tektronix part number 015-0572-XX SMA female to BNC male adapter. This adapter will plug onto the BNC on the front of the scope and connect to a SMA cable. For more questions please press the "Contact Us" button on the right of the screen.   
FAQ ID63516
What cart does my scope use?
Below are the Instrument Carts that can be purchased from Tektronix.                                         K4000                                                                             K420                              K475 More information can …
FAQ ID64561
How do I use the MDO3000 to generate a frequency response curve?
The MDO3000 boasts a 50 MHz noise generator as a feature in the function generator, which can be used in conjunction with the wide-capture-bandwidth spectrum analyzer to produce a frequency response curve for an electronic system or device. The noise …
FAQ ID69351
Can existing MSO3000/DPO3000  scopes be upgraded/modified to a MDO3000?
No, there is no conversion path to go from an existing MSO/DPO3000 to a new MDO3000. If you have more questions please contact one of our Technical Support Centers and an Application Engineer will quickly answer your questions. 
FAQ ID69326
If someone buys a MDO3000 with option R5 and after one year enables SA and AFG. Does the warranty option R5 apply to SA and AFG or do they have to purchase R5 for SA/AFG separately? 
Yes, all extended Service options, including R5, cover the specific MDO3000 instrument for which the option was purchased. Like product warranty, Service options are linked to a specific model and serial number.  Product warranty and extended Service …
FAQ ID69311
How do I know if an AC signal applied to the MDO3000/4000/B RF 50 Ω input is going to exceed the maximum input power rating, and cause clipping, or damage?
MDO3000, MDO4000/B Advanced Math equation will calculate the AC signal's equivalent RF power in dBm, and the automatic High measurement will determine the maximum average power level of the AC signal applied to the 50 Ω analog input channel. Caution: …
FAQ ID69366
If I upgrade my MDO3000 bandwidth do I receive higher bandwidth probes?
New, higher bandwidth probes are provided if the upgraded scope bandwidth exceeds the original supplied probes bandwidth.For example: If you upgrade a MDO3054 (500 MHz) to the MDO3104 (1GHz), you will also receive 4 TPP1000 (1 GHz probes) with the …
FAQ ID69381
Mixed Domain Oscilloscopes
Today's integrated designs need an oscilloscope that is just as integrated - such as the MDO3000 Mixed Domain Oscilloscope (MDO) Series. It is the ultimate 6-in-1 integrated oscilloscope that includes an integrated spectrum analyzer, arbitrary …

참고자료 번호: 48W-30020-11
Datasheet
MDO3000 Series
Oscilloscopes

Revision G: This manual contains the specifications and the performance verification procedures for the MDO3000 Series oscilloscopes. Released Sept 2019.


부품 번호: 077097900
성능 확인
MDO3000
Mixed-Domain Oscilloscopes

This service manual provides information that you need to troubleshoot,disassemble, and replace parts on the MDO3000 Series oscilloscopes.


부품 번호: 077098100
서비스
MDO4000C, MDO4000B, MDO4000, MSO4000B, DPO4000B, and MDO3000 Series
Digital Oscilloscopes

This manual explains the use of commands for remotely controlling youroscilloscope. With this information, you can write computer programs toperform functions, such as setting the front-panel controls, taking measurements, performing statistical calculations, and exporting data for use in other programs.


부품 번호: 077051009
프로그래머
MDO4000C, MDO4000B, MDO4000, MSO4000B, DPO4000B, and MDO3000 Series
Digital Oscilloscopes

This manual explains the use of commands for remotely controlling youroscilloscope. With this information, you can write computer programs toperform functions, such as setting the front-panel controls, taking measurements, performing statistical calculations, and exporting data for use in other programs.


부품 번호: 077051007
프로그래머
Read This First
Update Your MDO3000 with the Latest Firmware

This document is targeted to product users and explains operation and/or installation procedures.


부품 번호: 061440200
릴리스 노트
KickStart Instrument Control Software Version 2.2.0 (Windows 10, 8, 7 compatible)
"KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the …

부품 번호: KICKSTART-2.2.0
애플리케이션
KickStart Instrument Control Software Version 2.1.1 (Windows 10, 8, 7 compatible)
"KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the …

부품 번호: KICKSTART-2.1.1
애플리케이션
TEKVISA Connectivity Software - V4.2.0
TekVISA is the Tektronix implementation of VISA (Virtual Instrument Software Architecture), an industry-standard communication protocol.When installed on a PC, TekVISA provides communication with instruments that are connected to the PC via various …

부품 번호: 066093812
드라이버
DPO2000, MSO2000, DPO3000 and DPO4000, MSO3000 and MSO4000, MDO3000 and MDO4000 and MDO3 IVI Driver - V1.5
The Tektronix MSO/DPO2000, MDO/MSO/DPO3000, MDO/MSO/DPO4000 and MDO3 IVI Driver is an IVI class-compliant driver. It complies with Scope Class specifications (IVI-4.1) as defined by the IVI foundation. An IVI class-compliant specific driver for an …

부품 번호: 066133104
드라이버
KickStart Instrument Control Software Version 2.1.0 (Windows 10, 8, 7 compatible)
"KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the …

부품 번호: KICKSTART-2.1.0
애플리케이션
MDO3K FIRMWARE RELEASE - v1.30
MDO3000 firmware update

부품 번호: 066158611
펌웨어
MDO3000 FIRMWARE - V1.26
This Firmware is an upgrade for all MDO3000 Series oscilloscopes.

부품 번호: 066158609
펌웨어
TEKVISA CONNECTIVITY SOFTWARE - V4.1.1
TekVISA is the Tektronix implementation of VISA (Virtual Instrument Software Architecture), an industry-standard communication protocol.When installed on a PC, TekVISA provides communication with instruments that are connected to the PC via various …

부품 번호: 066093811
드라이버
MDO3000 FIRMWARE - V1.24
This Firmware is an upgrade for all MDO3000 Series oscilloscopes.

부품 번호: 066158608
펌웨어
Tektronix Openchoice Desktop Application TDSPCS1 - v2.6
The Tektronix OpenChoice Desktop free application lets you capture oscilloscope screen images, waveform data, and settings from a Microsoft Windows computer. After installing the software, refer to the section “Connecting to a PC” in your …

부품 번호: 066093914
유틸리티
MDO3000 FIRMWARE, V1.20
This Firmware is an upgrade for all MDO3000 Series oscilloscopes.

부품 번호: 066158606
펌웨어
Tektronix Toolbars for Microsoft Office 32 bit - V4.0.4
Tektronix Toolbars for Microsoft Office v4.0.4 provide toolbars (add-ins) for the 32 bit versions of Microsoft Excel and Microsoft Word. This version of Toolbars requires OpenChoice TekVISA v4.0.4 (Part Number 066093809) to be preinstalled on the PC …

부품 번호: 066133202
유틸리티
TEKVISA CONNECTIVITY SOFTWARE, V4.0.4
TekVISA is the Tektronix implementation of VISA (Virtual Instrument Software Architecture), an industry-standard communication protocol. When installed on a PC, TekVISA provides communication with instruments that are connected to the PC via various …

부품 번호: 066093809
드라이버
Probing Techniques for Accurate Voltage Measurements on Power Supplies with Oscilloscopes
Making oscilloscope voltage measurements on power supplies is fundamental, but not without challenges. Much is  written on oscilloscopes, but probing techniques are often taken for granted. This application note focuses on probing and …

참고자료 번호: 51W-60161-3
애플리케이션 노트
Accurate Measurements Matter
The MDO3000 Series scope is designed to make the most accurate measurements in the industry. While many other instruments only offer low-resolution display data, the MDO3000 takes measurements on actual acquisition data, providing an unrivaled view …

참고자료 번호: 48W-60968-2
팩트 시트
Automated Frequency Response Measurement with AFG31000, MDO3000, and TekBench™ Instrument Control Software
This application note describes how to use TekBench™ Software and a Tektronix AFG31000 series arbitrary function generator and an MDO3000 oscilloscope to perform the automated frequency response measurement effortlessly within just a few steps.

참고자료 번호: 48W-61517-0
애플리케이션 노트
MDO3000 Spectrum Analyzer vs. Oscilloscope FFT Comparison Fact Sheet
Mixed Domain Oscilloscopes have built-in spectrum analyzers with a dedicated RF input for significantly higher dynamic range than an oscilloscope with FFT. This fact sheet compares the performance of the MDO3000’s built-in spectrum analyzer to common …

참고자료 번호: 48W-30079-2
팩트 시트
MDO4000C and MDO3000 Series Comparison Fact Sheet
This fact sheet compares features and specifications of MDO4000C and MDO3000 Series mixed domain oscillscopes.

참고자료 번호: 48W-30086-2
선택 가이드
MDO3000 Series vs. Agilent N9320B Spectrum Analyzer
Side-by-side comparison on key specifications, automated markers, plus highlights of the key features of  the MDO3000:Capture bandwidthSpectogram displayIntegration with scope, logic, and protocol analysis

참고자료 번호: 48W-30244-0
경쟁사
10 Factors in Choosing a Basic Oscilloscope.
This guide will give you a quick overview of the key factors that determine the suitability of a basic oscilloscope for the job at hand. Learn the XYZ's of Oscilloscopes »  

참고자료 번호: 3GW_60848_1
브로슈어
SOLUTIONS FOR SCIENTIFIC AND ENGINEERING RESEARCH

참고자료 번호: 55W_30503_2
브로슈어
Automotive Solutions Brochure
The pace of change in automotive electronics has never been faster, resulting in safer, more efficient, and more connected vehicles. Technologies such as high-speed data communications, wireless communications, radar, and power supplies underpin …

참고자료 번호: 45W-60646_1
브로슈어
Power Supply Measurement & Analysis with Bench Oscilloscopes
Today’s power supplies are driving to a level of efficiency never seen before, requiring design engineers to perform specialized power measurements that are time-consuming and complex. Learn how using a Tektronix Bench Oscilloscopes provides fast …

참고자료 번호: 3GZ-23612-6
애플리케이션 노트
Power Supply Measurement and Analysis Primer
A power supply is a component, subsystem, or system that converts electrical power from one form to another; commonly from alternating current (AC) utility power to direct current (DC) power. The proper operation of electronic devices ranging from …

참고자료 번호: 55T-18412-6
입문서
Testing a New Switch Mode Power Supply Design Poster
Get a quick overview of the key measurements for verifying a new switch mode power supply (SMPS) design.  This poster shows key measurements, from verifying your prototype during initial startup, to optimizing switching loss and magnetic losses, to …

참고자료 번호: 46W-60156-0
포스터
Making Accurate Current Measurements on Power Supplies with Oscilloscopes
Accurately measuring current with oscilloscopes is essential for power supply design and general electronics. Learn how to measure current using shunt resistors and voltage probes, and how to use clamp-on current probes with your oscilloscope. Get …

참고자료 번호: 51W-60171-2
애플리케이션 노트
Oscilloscope Selection Guide
From basic signal-checking to high-performance analysis, this selection guide gives an overview of the complete range of oscilloscopes from Tektronix. Comparison tables give high-level specifications and features, and indicate the major differences …

참고자료 번호: 46W-31080-7
선택 가이드
Identifying Setup and Hold Violations with a Mixed Signal Oscilloscope
Problems with setup and hold timing are among the most challenging to identify.  Mixed signal oscilloscopes (MSOs) are able to capture both analog and digital representations of signals, making them well-suited for identifying digital timing problems …

참고자료 번호: 55W-61095-0
애플리케이션 노트
3 Series MDO vs. MDO3000 Series
This fact sheet compares important specifications and features of the Tektronix 3 Series MDO Mixed Domain Oscilloscope to those of the Tektronix MDO3000 Series Oscilloscopes.

참고자료 번호: 48W-61605-0
팩트 시트
How to Minimize Probe Loading with Low Capacitance Probes
Probing a circuit always has some impact on signals. Probe loading changes the signal being probed and can cause measurement problems or can even cause a circuit to perform differently. Reducing capacitive loading can help minimize these effects. In …

참고자료 번호: 51W-26294-6
애플리케이션 노트
Tektronix MDO3000 Series Oscilloscope
This demonstration guide takes you through a series of step-by-step demonstrations on how the MDO3000 Series oscilloscope helps simplify the debug of mixed signal designs with its powerful functionality and integrated test instruments. This …

참고자료 번호: 48W-29903-0
사용 방법 가이드
MDO Signal Path Teardown Poster
MDO4000 and MDO3000 Mixed Domain Oscilloscopes deliver uncompromised oscilloscope performance combined with spectrum analyzer performance on par with standalone spectrum analyzers. But how do they do it? The answer lies in Tektronix’ custom ASICs, a …

참고자료 번호: 48W-60186-2
포스터
Serial Support Using Tektronix Oscilloscopes and Optional Software
Tektronix oscilloscopes offer a portfolio of optional analysis capabilities to simplify serial bus debug or compliance verification. This selection matrix shows which serial standards are supported by each of the oscilloscope series.  

참고자료 번호: 55W-29028-13
선택 가이드
Replicating Real World Signals with an Arbitrary/Function Generator
Learn how to simulate sensor and bus signals on an arbitrary waveform generator.  Find out how to capture signals using an oscilloscope, edit them using PC software, and play them back on an arbitrary/function generator.

참고자료 번호: 76W-18661-2
애플리케이션 노트
MDO3000 FIRMWARE, V1.18
This firmware is an upgrade for all MDO3000 Series oscilloscopes.

부품 번호: 066158605
펌웨어
MDO3000 FIRMWARE, V1.14
This firmware is an upgrade for all MDO3000 Series oscilloscopes.

부품 번호: 066158604
펌웨어
MDO3000 FIRMWARE, V1.12
This firmware is an upgrade for all MDO3000 Series oscilloscopes.

부품 번호: 066158603
펌웨어
ARBEXPRESS WAVEFORM CREATION AND EDITING SW, V3.1
ArbExpress is a waveform creation and editing tool for Tektronix AWG and AFG instruments. It provides an easy to use and efficient way to create and edit waveforms, transfer waveforms to and from Arbitrary Waveform Generators (AWG), and …

부품 번호: 066146103
애플리케이션
MDO3000 Oscilloscope Upgrade Fact Sheet
The MDO3000 Series Mixed Domain Oscilloscope lets you add capabilities as your needs change.  This fact sheet gives a quick overview of the upgrades available for the MDO3000.

참고자료 번호: 48W-30148-1
팩트 시트
MDO3000 Series vs. Agilent MSO/DSO3000 X-Series
This 2-page fact sheet compares the features and key specifications of the Tektronix MDO3000 Series oscilloscopes to the Agilent 3000 X-Series.

참고자료 번호: 48W-30078-2
경쟁사
MDO3000 Series vs. Agilent MSO/DSO3000 X-Series
Examine the MDO3000 Series vs. the Agilent MSO/DSO3000 X-Series.

참고자료 번호: 48W-30078-0
경쟁사
MDO3000 Series vs. Keysight X3000T Series Oscilloscopes
This 2-page fact sheet compares the features and specifications of Tektronix MDO3000 Series Mixed Domain Oscilloscopes to Keysight X3000T Series oscilloscopes.

참고자료 번호: 3GA-60137-0
경쟁사
Measurements Matter Flyer

참고자료 번호: 48W-60968-1
특징
장비 최대한활용하기
텍트로닉스 오실로스코프 소프트웨어,프로브 및 악세사리를 사용하면 오실로스코프를 특정 애플리케이션 요구사항 및 환경에 맞출 수 있습니다.

참고자료 번호: 60W_14232_10
제품 선택 가이드
XYZs of Oscilloscopes Primer
After reading this primer, you will be able to:Describe how oscilloscopes workDescribe the differences between analog, digital storage, digital phosphor, and digital sampling oscilloscopesDescribe electrical waveform typesUnderstand basic …

참고자료 번호: 03Z-8605-7
입문서
오실로스코프 입문서
본 입문서는 60페이지 분량으로 오실로스코프의 기본 사항과 조작을 이해하는 데 적합합니다. 신호 무결성의 중요성, 오실로스코프의 작동 원리, 파형 측정 결과를 해석하는 방법과 같은 기초적인 개념에 대해 설명되어 있습니다.

참고자료 번호: 03K-8605-5
입문서
Wave Inspector® 탐색 및 검색: 파형 분석이 간편해집니다.
무어의 법칙에 따라 전자 기술이 더욱 빠르게 발전하면서, 시스템 설계는 점점 복잡해지고 이에 따라설계, 구축, 문제해결 및 고장 시 수리도 어려워지고 있습니다. 그러면 이것이 최신 오실로스코프에는 어떤 의미를 주는 걸까요?

참고자료 번호: 48T-19039-9
애플리케이션 노트
Everyday Design & Debug with the MDO3000 Mixed Domain Oscilloscope
Save hours verifying and debugging your designs using a scope developed to make your job simpler and faster. Work from DC to RF, with analog and digital signals, and serial and parallel buses.

참고자료 번호: 48W-30067-0
애플리케이션 개요
혼합 신호 임베디드 설계 디버깅
일반적으로 임베디드 설계에는 다양한 아날로그 신호, 고속 및 저속 직렬 디지털 통신 및 마이크로프로세서 버스 등이 통합되는 경우가 많습니다. 이 애플리케이션 노트는 MSO4000 시리즈 혼합 신호 오실로스코프를 이용하여 혼합 신호 임베디드 설계를 디버깅하는 방법을 설명하고 있습니다.

참고자료 번호: 3GK-20215-1
애플리케이션 노트
Introduction to Video Measurements
In this application note, we demonstrate using a MSO/DPO5000, MDO/MSO/DPO4000 and MDO/MSO/DPO3000 Series Oscilloscope to make a variety of video measurements that are common in standard and high definition systems.

참고자료 번호: 3GW-20975-2
애플리케이션 노트
임베디드 시스템 설계의 저속 직렬 버스 디버깅
일반적인 임베디드 시스템은 켜지자마자 특수 목적을 지닌 애플리케이션을 실행하며 시작 하고 꺼질 때까지는 작동이 멈추지 않습니다. 사실상, 오늘날 설계되고 생산되는 모든 전자 장치는 임베디드 시스 템입니다. 임베디드 시스템의 예로는 다음과 같은 것이 있습니다.

참고자료 번호: 48W-19040-21
애플리케이션 노트
MDO3000 Series vs. Agilent/Keysight X3000 Series True Cost of Your Scope
When comparing oscilloscopes, don’t forget to look at the “hidden” costs to get the configuration you need.

참고자료 번호: 48W-30247-0
경쟁사
MDO3000 Series Configuration Fact Sheet
Step by step guide to configure your MDO3000 for your application, in a handy two-page format.

참고자료 번호: 48W-30033-1
팩트 시트
MDO3000 Series Product Selection and Comparison Guide
This guide helps with the selection and comparison process as you research the MDO3000. It explains key specifications for oscilloscopes, spectrum analyzers and arbitrary function generators.  It also provides a comparison template.

참고자료 번호: 48W-30076-0
선택 가이드
MDO3000 시리즈 사용 설명서
혼합 도메인 오실로스코프

이 MDO3000 시리즈 사용 설명서에는 오실로스코프의 작동 방식이 설명되어 있고 설치 절차가 포함되어 있습니다. 또한 기능 및 애플리케이션에 대한 정보도 제공합니다.


부품 번호: 077097702
주 사용자
MDO3000 시리즈 사용 설명서
혼합 도메인 오실로스코프 User Manual

이 MDO3000 시리즈 사용 설명서에는 오실로스코프의 작동 방식이 설명되어 있고 설치 절차가 포함되어 있습니다. 또한 기능 및 애플리케이션에 대한 정보도 제공합니다.
부품 번호: 077097701
주 사용자
MDO3000 Series
Oscilloscopes User Manual

This MDO3000 series Installation and Safety Manual explains basic safety and installation procedures.
부품 번호: 071324902
사용자
MDO3000 Series Oscilloscope
Declassification and Security Instructions

This document helps customers with data security concerns to sanitize or remove memory devices from the Tektronix MDO3000 Series Mixed Domain Oscilloscopes.
부품 번호: 077098000
기밀 해제
MDO3000 Series
Oscilloscopes User Manual

This MDO3000 series Installation and Safety Manual explains basic safety and installation procedures.
부품 번호: 071324901
사용자
MDO4000B, MDO4000, MSO4000B, DPO4000B, and MDO3000 Series
Digital Oscilloscopes Programmer Manual

This manual explains the use of commands for remotely controlling your oscilloscope. With this information, you can write computer programs to perform functions, such as setting the front-panel controls, taking measurements, performing statistical calculations, and exporting data for use in other programs.
부품 번호: 077051006
프로그래머
MDO3000 Series
Oscilloscopes User Manual

This MDO3000 series Installation and Safety Manual explains basic safety and installation procedures.
부품 번호: 071324900
사용자
MDO3000 시리즈 사용 설명서
혼합 도메인 오실로스코프 User Manual

이 MDO3000 시리즈 사용 설명서에는 오실로스코프의 작동 방식이 설명되어 있고 설치 절차가 포함되어 있습니다. 또한 기능 및 애플리케이션에 대한 정보도 제공합니다.
부품 번호: 077097700
주 사용자
MDO3000 Series
Oscilloscopes Technical Reference

This manual contains the specifications and the performance verification procedures for the MDO3000 Series oscilloscopes.
부품 번호: 077097900
성능 확인
MDO3000 Series
Oscilloscopes Application Module Installation Manual

This document contains procedures for installing and verifying MDO3AERO, MDO3AUDIO, MDO3AUTO, MDO3COMP, MDO3EMBD, MDO3FLEX, MDO3USB, MDO3LMT, MDO3PWR application modules in MDO3000 oscilloscopes.
부품 번호: 071325000
사용자