Spectrum Analyzer

RF input frequency range

9 kHz to 6.2 GHz

Frequency reference accuracy

Initial accuracy at calibration

±3 ppm + aging (after 20 minute warmup at 18 °C to 28 °C ambient)

Accuracy, typical

±20 ppm + aging (after 20 minute warm up at -10 °C to 55 °C ambient)

Aging, typical

± 3 x 10^-6 (1^st year), ±1 x 10^-6/year thereafter

External frequency reference input

Input frequency range

10 MHz ±10 Hz

Input level range

-10 dBm to +10 dBm sinusoid

Impedance

50 Ω

Center frequency resolution

Block IQ samples

1 Hz

Streamed ADC samples

500 kHz

RF input impedance

50 Ω

RF input VSWR (typical)

≤ 1.8:1 (10 MHz to 6200 MHz, reference level ≥ +10 dBm)

(Equivalent Return Loss: ≥11 dB)

Maximum RF input level without damage

DC voltage

±40 V_DC

Reference level ≥ –10 dBm

+23 dBm (continuous or peak)

Reference level < –10 dBm

+15 dBm (continuous or peak)

Maximum RF input operating level

The maximum level at the RF input for which the instrument will meet its measurement specifications.

Center frequency < 22 MHz (low-frequency path)

+15 dBm

Center frequency ≥22 MHz (RF path)

+20 dBm

Amplitude accuracy at all center frequencies

Center frequency	Warranted (18 °C to 28 °C)	Typical (95% confidence) (18 °C to 28 °C)	Typical (-10 °C to 55 °C)
9 kHz - < 3 GHz	±1.2 dB	±0.8 dB	±1.0 dB
≥ 3 GHz - 6.2 GHz	±1.65 dB	±1.0 dB	±1.5 dB

Reference level +20 dBm to -30 dBm, alignment run prior to testing.

Applies to corrected IQ data, with signal to noise ratios > 40 dB.

The above specifications apply when operated and stored at the average factory calibration absolute humidity conditions (8 grams of water per cubic meter of air). Additional humidity specifications are provided in the Specifications and Performance Verification Technical Reference.

IF bandwidth

40 MHz

ADC sample rate and bit width

112 Ms/s, 14 bits

Real-time IF acquisition data (uncorrected)

112 Ms/s, 16-bit integer real samples

40 MHz BW, 28 ±0.25 MHz Digital IF, uncorrected. Corrected values are stored with saved files

Block streaming data at an average rate of 224 MB/s

Block baseband acquisition data (corrected)

Maximum acquisition time

1 second

Bandwidths

≤ 40 /( 2^N) MHz, 0 Hz Digital IF, N ≥ 0

Sample rates

≤ 56 / (2^N) Msps, 32-bit float complex samples, N ≥ 0

Channel amplitude flatness

Reference level +20 dBm to -30 dBm, alignment run before testing. Applies to corrected IQ data, with signal to noise ratios >40 dB.

Center frequency range	Warranted	Typical
	18 ⁰C to 28 ⁰C
24 MHz to 6.2 GHz	±1.0 dB	±0.4 dB
22 MHz to 24 MHz	±1.2 dB	±1.0 dB
	-10 ⁰C to 55 ⁰C
24 MHz to 6.2 GHz	---	±0.5 dB
22 MHz to 24 MHz	---	±2.5 dB

Trigger/sync input

Voltage range

TTL, 0.0 V – 5.0 V

Trigger level, positive-going threshold voltage

1.6 V minimum; 2.1 V maximum

Trigger level, negative-going threshold voltage

1.0 V minimum; 1.35 V maximum

Impedance

10 kΩ

IF power trigger

Threshold range

0 dB to -50 dB from reference level, for trigger levels > 30 dB above the noise floor

Type

Rising or falling edge

Trigger re-arm time

≤100 μs

Displayed Average Noise Level (DANL)

Reference level = -50 dBm, input terminated with 50 Ω load, log-average detection (10 averages). SignalVu-PC Spectrum measurements with Span > 40 MHz may use LF or RF path in the first segment of the spectrum sweep.

Center frequency	Frequency range	DANL (dBm/Hz)	DANL (dBm/Hz), typical
< 22 MHz (LF path)	100 kHz - 42 MHz	≤-130	-133
≥ 22 MHz (RF path)	2 MHz - <5 MHz	≤-145	≤-148
	5 MHz - <1.0 GHz	≤-161	≤-163
	1.0 GHz - <1.5 GHz	≤-160	≤-162
	1.5 GHz - <2.5 GHz	≤-157	≤-159
	2.5 GHz - <3.5 GHz	≤-154	≤-156
	3.5 GHz - <4.5 GHz	≤-152	≤-155
	4.5 GHz - 6.2 GHz	≤-149	≤-151

Phase noise

Phase noise measured with 1 GHz CW signal at 0 dBm.

The following table entries are in dBc/Hz units.

	Center frequency
Offset	1 GHz	10 MHz (typical)	1 GHz (typical)	2.5 GHz (typical)	6 GHz (typical)
1 kHz	≤-84	≤-115	≤-89	≤-78	≤-83
10 kHz	≤-84	≤-122	≤-87	≤-84	≤-85
100 kHz	≤-88	≤-126	≤-93	≤-92	≤-95
1 MHz	≤-118	≤-127	≤-120	≤-114	≤-110

Residual spurious response, typical

(Reference level ≤ -50 dBm, RF input terminated with 50 Ω load)

CF range 9 kHz - < 1 GHz

< -100 dBm

CF range 1 GHz - < 3 GHz

< -95 dBm

CF range 3 GHz - 6.2 GHz

< -90 dBm

With these exceptions for LO related spurs

< -80 dBm: 2080-2120 MHz

< -80 dBm: 3895-3945 MHz

< -85 dBm: 4780-4810 MHz

Residual FM

< 10 Hz_P-P (95% confidence)

3^RD order IM distortion

Two CW signals, 1 MHz separation, each input signal level 5 dB below the reference level setting at the RF input Reference level at-15 dBm disables Preamp; reference level at -30 dBm enables Preamp.

Center frequency 2130 MHz

≤ -63 dBc at reference level -15 dBm, 18 ⁰C to 28 ⁰C

≤ -63 dBc, at reference level -15 dBm, -10 ⁰C to 55 ⁰C, typical

≤ -63 dBc, at reference level -30 dBm, typical

40 MHz to 6.2 GHz, typical

< -58 dBc at reference level = -10 dBm

< -50 dBc at reference level = -50 dBm

3^RD order intercept (TOI)

Center frequency 2130 MHz

≥ +13 dBm at reference level -15 dBm, 18 ⁰C to 28 ⁰C

≥ +13 dBm, at reference level -15 dBm, -10 ⁰C to 55 ⁰C, typical

≥ -2 dBm, at reference level -30 dBm, typical

40 MHz to 6.2 GHz, typical

+14 dBm at reference level -10 dBm

-30 dBm at reference level -50 dBm

2^ND harmonic distortion, typical

< -55 dBc, 10 MHz to 300 MHz, reference level = 0 dBm

< -60 dBc, 300 MHz to 3.1 GHz, reference level = 0 dBm

< -50 dBc, 10 MHz to 3.1 GHz, reference level = -40 dBm

Exception: < -45 dBc in the range 1850-2330 MHz

2^ND harmonic intercept (SHI)

+55 dBm, 10 MHz to 300 MHz, reference level = 0 dBm

+60 dBm, 300 MHz to 3.1 GHz, reference level = 0 dBm

+10 dBm, 10 MHz to 3.1 GHz, reference level = -40 dBm (Exception: +5 dBm in the range 1850-2330 MHz)

Input related spurious response (SFDR)

Input frequencies at ≤ 6.2 GHz and 18 - 28 ºC

Level	Center frequency range
Spurious responses due to the following mechanisms: RFx2*LO1, 2RFx2*LO1, RFx3LO1, RFx5LO1, RF to IF feedthrough, IF2 image
≤ -60 dBc	≤ 6200 MHz
Spurious responses due to 1st IF images (RFxLO1)
≤ -60 dBc	< 2700 MHz
≤ -50 dBc	2700 - 6200 MHz

With these exceptions at ≤ 6.2 GHz and 18 - 28 ºC, typical

Type	Level	Center frequency range
IF feedthrough	≤ -45 dBc	1850 - 2700 MHz
1st IF image	≤ -55 dBc	1850 - 1870 MHz
	≤ -35 dBc	3700 - 3882 MHz
	≤ -35 dBc	5400 - 5700 MHz
2nd IF image	≤ -50 dBc	22 - 1850 MHz
	≤ -50 dBc	4175 - 4225 MHz
RFx2LO	≤ -50 dBc	4750 - 4810 MHz
2RFx2LO	≤ -50 dBc	3900 - 3840 MHz
RFx3LO	≤ -45 dBc	4175 - 4225 MHz

Spurious responses due to ADC images at 18 - 28 ºC

Level	Center frequency range
≤ -60 dBc	Offset from center frequency > 56 MHz
≤ -50 dBc	56 MHz ≥ offset from center frequency ≥ 36 MHz

Local oscillator feedthrough to input connector

< -75 dBm at reference level = -30 dBm

Audio output (from SignalVu-PC or application programming interface)

Types

AM, FM

IF bandwidth range

Five selections, 8 kHz – 200 kHz

Audio output frequency range

50 Hz – 10 kHz

PC audio output

16 bits at 32 ks/s

Audio file output format

.wav format, 16 bit, 32 ks/s

Signal Strength display

Signal strength indicator

Located at right side of display

Measurement bandwidth

Up to 40 MHz, dependent on span and RBW setting

Tone type

Variable frequency based on received signal strength

Spectrum and Spurious display

Traces

Three traces + 1 math trace + 1 trace from spectrogram for Spectrum display; four traces for Spurious display

Trace functions

Normal, Average (VRMS), Max Hold, Min Hold, Average of Logs

Detector

Average (VRMS), Average (of logs), CISPR peak, +Peak, Sample for Spectrum only -Peak; when Option SVQP is enabled, CISPR Quasi Peak and Average

Spectrum trace length

801, 2401, 4001, 8001,10401, 16001, 32001, and 64001 points

RBW range

1.18 Hz to 8 MHz for Spectrum display

Full span sweep speed

1 MHz

16.5 GHz/sec

100 kHz

16.5 GHz/sec

10 kHz

13.7 GHz/sec

1 kHz

1.9 GHz/sec

Related information:

Measured using a Panasonic Toughpad FZ-G1, Intel® Core™ i5-5300U 2.3GHz Processor, 8GB RAM, 256GB SSD, Windows®7 Pro. Spectrum display only measurement on screen.

DPX spectrogram display

Trace detection

+Peak, -Peak, Average(V_RMS)

Trace length, memory depth

801 (60,000 traces)

2401 (20,000 traces)

4001 (12,000 traces)

Time resolution per line

1 ms to 6400 s, user selectable

Measurements (nominal)

Pulse-Ogram™ waterfall display of multiple segmented captures, with amplitude vs time and spectrum of each pulse. Pulse frequency, Delta Frequency, Average on power, Peak power, Average transmitted power, Pulse width, Rise time, Fall time, Repetition interval (seconds), Repetition interval (Hz), Duty factor (%), Duty factor (ratio), Ripple (dB), Ripple (%), Droop (dB), Droop (%), Overshoot (dB), Overshoot (%), Pulse- Ref Pulse frequency difference, Pulse- Ref Pulse phase difference, Pulse-Pulse frequency difference, Pulse- Pulse phase difference, RMS frequency error, Max frequency error, RMS phase error, Max phase error, Frequency deviation, Phase deviation, Impulse response (dB),Impulse response (time), Time stamp.

Minimum pulse width for detection, typical

150 ns

Average ON power at 18 °C to 28 °C, typical

±1.0 dB + absolute amplitude accuracy

For pulses of 300 ns width or greater, duty cycles of .5 to .001, and S/N ratio ≥ 30 dB

Duty factor, typical

±0.2% of reading

For pulses of 450 ns width or greater, duty cycles of .5 to .001, and S/N ratio ≥ 30 dB

Average transmitted power, typical

±1.0 dB + absolute amplitude accuracy

For pulses of 300 ns width or greater, duty cycles of .5 to .001, and S/N ratio ≥ 30 dB

Peak pulse power, typical

±1.5 dB + absolute amplitude accuracy

For pulses of 300 ns width or greater, duty cycles of .5 to .001, and S/N ratio ≥ 30 dB

Pulse width, typical

±0.25% of reading

For pulses of 450 ns width or greater, duty cycles of .5 to .001, and S/N ratio ≥ 30 dB

Modulation formats

BPSK, QPSK, 8PSK, 16QAM, 32QAM, 64QAM, 128QAM, 256QAM, π/2DBPSK, DQPSK, π/4DQPSK, D8PSK, D16PSK, SBPSK, OQPSK, SOQPSK, 16-APSK, 32-APSK, MSK, GFSK, CPM, 2FSK, 4FSK, 8FSK, 16FSK, C4FM

Analysis period

Up to 163,500 samples

Measurement filter

Root Raised Cosine, Raised Cosine, Gaussian, Rectangular, IS-95 TX_MEA, IS-95 Base TXEQ_MEA, None

Reference Filter

Gaussian, Raised Cosine, Rectangular, IS-95 REF, None

Filter rolloff factor

α：0.001 to 1, in 0.001 steps

Measurements

Constellation, Demod I&Q vs. Time, Error Vector Magnitude (EVM) vs. Time, Eye Diagram, Frequency Deviation vs. Time, Magnitude Error vs. Time, Phase Error vs. Time, Signal Quality, Symbol Table, Trellis Diagram

Maximum symbol rate

240 M symbols/s

Modulated signal must be contained entirely within the acquisition bandwidth

Adaptive equalizer

Linear, Decision-Directed, Feed-Forward (FIR) equalizer with coefficient adaptation and adjustable convergence rate. Supports modulation types BPSK, QPSK, OQPSK, DQPSK, π/2DBPSK, π/4DQPSK, 8PSK, D8SPK, D16PSK, 16/32/64/128/256-QAM, 16/32-APSK

QPSK Residual EVM (center frequency = 2 GHz), typical mean

1.1 % (100 kHz symbol rate)

1.1 % (1 MHz symbol rate)

1.2 % (10 MHz symbol rate)

2.5 % (30 MHz symbol rate)

400 symbols measurement length, 20 Averages, normalization reference = maximum symbol magnitude

256 QAM Residual EVM (center frequency = 2 GHz), typical mean

0.8 % (10 MHz symbol rate)

1.5 % (30 MHz symbol rate)

400 symbols measurement length, 20 Averages, normalization reference = maximum symbol magnitude

Measurements

WLAN power vs. time; WLAN symbol table; WLAN constellation; spectrum emission mask; error vector magnitude (EVM) vs. symbol (or time), vs subcarrier (or frequency); mag error vs symbol (or time), vs. subcarrier (or frequency); phase error vs symbol (or time), vs. subcarrier (or frequency); channel frequency response vs. symbol (or time), vs. subcarrier (or frequency); spectral flatness vs. symbol (or time), vs. subcarrier (or frequency)

Residual EVM - 802.11a/g/j /p (OFDM), 64-QAM, typical

2.4 GHz, 20 MHz BW: -38 dB

5.8 GHz, 20 MHz BW: -38 dB

Input signal level optimized for best EVM, average of 20 bursts, ≥16 symbols each

Residual EVM - 802.11b, CCK-11, typical

2.4 GHz, 11 Mbps: 2.0 %

Input signal level optimized for best EVM, average of 1,000 chips, BT = .61

Measurements

WLAN power vs. time; WLAN symbol table; WLAN constellation; spectrum emission mask; error vector magnitude (EVM) vs. symbol (or time), vs subcarrier (or frequency); mag error vs symbol (or time), vs. subcarrier (or frequency); phase error vs symbol (or time), vs. subcarrier (or frequency); channel frequency response vs. symbol (or time), vs. subcarrier (or frequency); spectral flatness vs. symbol (or time), vs. subcarrier (or frequency)

EVM performance - 802.11n, 64-QAM, typical

2.4 GHz, 40 MHz BW: -35 dB

5.8 GHz, 40 MHz BW: -35 dB

Input signal level optimized for best EVM, average of 20 bursts, ≥16 symbols each

Measurements

WLAN power vs. time; WLAN symbol table; WLAN constellation; spectrum emission mask; error vector magnitude (EVM) vs. symbol (or time), vs subcarrier (or frequency); mag error vs symbol (or time), vs. subcarrier (or frequency); phase error vs symbol (or time), vs. subcarrier (or frequency); channel frequency response vs. symbol (or time), vs. subcarrier (or frequency); spectral flatness vs. symbol (or time), vs. subcarrier (or frequency)

EVM performance - 802.11ac, 256-QAM, typical

5.8 GHz, 40 MHz BW: -35 dB

Input signal level optimized for best EVM, average of 20 bursts, ≥16 symbols each

Measurements

RF output power, operating frequency accuracy, modulation emission spectrum, unwanted emissions spurious, adjacent channel power ratio, frequency deviation, modulation fidelity, frequency error, eye diagram, symbol table, symbol rate accuracy, transmitter power and encoder attack time, transmitter throughput delay, frequency deviation vs. time, power vs. time, transient frequency behavior, HCPM transmitter logical channel peak adjacent channel power ratio, HCPM transmitter logical channel off slot power, HCPM transmitter logical channel power envelope, HCPM transmitter logical channel time alignment, cross-correlated markers.

Modulation fidelity, typical

C4FM = 1.3%

HCPM = 0.8%

HDQPSK = 2.5%

Input signal level is optimized for best modulation fidelity.

Supported standards

Bluetooth® 4.2 Basic Rate, Bluetooth® 4.2 Low Energy, Bluetooth® 4.2 Enhanced Data Rate. Bluetooth® 5 when SV31 is enabled.

Measurements

Peak Power, Average Power, Adjacent Channel Power or InBand Emission mask, -20 dB Bandwidth, Frequency Error, Modulation Characteristics including ΔF1avg (11110000), ΔF2avg (10101010), ΔF2 > 115 kHz, ΔF2/ΔF1 ratio, frequency deviation vs. time with packet and octet level measurement information, Carrier Frequency f0, Frequency Offset (Preamble and Payload), Max Frequency Offset, Frequency Drift f1-f0, Max Drift Rate fn-f0 and fn-fn-5, Center Frequency Offset Table and Frequency Drift table, color-coded Symbol table, Packet header decoding information, eye diagram, constellation diagram

Output power (BR and LE), typical mean

Supported measurements: Average power, peak power

Level uncertainty: refer to instrument amplitude and flatness specification

Measurement range: signal level > –70 dBm

Modulation characteristics, typical mean

Supported measurements: ΔF1avg, ΔF2avg, ΔF2avg/ ΔF1avg, ΔF2max%>=115kHz (basic rate), ΔF2max%>=115kHz (low energy)

Deviation range: ±280 kHz

Deviation uncertainty (at 0 dBm):

• 2 kHz + instrument frequency uncertainty (basic rate)
• 3 kHz + instrument frequency uncertainty (low energy)

Measurement range: Nominal channel frequency ±100 kHz

Initial Carrier Frequency Tolerance (ICFT) (BR and LE), typical mean

Measurement uncertainty (at 0 dBm): <1 kHz 2 + instrument frequency uncertainty

Measurement range: Nominal channel frequency ±100 kHz

Carrier Frequency Drift (BR and LE), typical mean

Supported measurements: Max freq. offset, drift f1- f0, max drift fn-f0, max drift fn-fn-5 (BR and LE 50 μs)

Measurement uncertainty: <2 kHz + instrument frequency uncertainty

Measurement range: Nominal channel frequency ±100 kHz

In-band emissions (ACPR) (BR and LE)

Level uncertainty: refer to instrument amplitude and flatness specification

LTE Downlink RF measurements (SV28xx-SVPC)

Standard Supported

3GPP TS 36.141 Version 12.5

Frame Format supported

FDD and TDD

Measurements and Displays Supported

Adjacent Channel Leakage Ratio (ACLR), Spectrum Emission Mask (SEM), Channel Power, Occupied Bandwidth, Power vs. Time showing Transmitter OFF power for TDD signals and LTE constellation diagram for Primary Synchronization Signal and Secondary Synchronization Signal with Cell ID, Group ID, Sector ID, RS (Reference Signal) Power and Frequency Error.

ACLR with E-UTRA bands (typical, with noise correction)

1st Adjacent Channel 60 dB

2nd Adjacent Channel 62 dB

5G NR Uplink/Downlink measurements (5GNRNL-SVPC)

Standard supported

TS 38.141-1 for BS and 38.521-1 for UE

Modulation accuracy

Sec 6.5.2 for BS and Sec 6.4.2 for UE.

ACP

Sec 6.6.3 for BS and Sec 6.5.2.4 for UE

Frame format supported

Uplink (FDD and TDD)

Downlink (FDD and TDD)

Measurements and displayssupported

Channel Power (CHP), Adjacent Channel Power (ACP), Power Vs Time (PVT)1, Modulation Accuracy (including Error Vector Magnitude (EVM), Frequency Error, IQ Error), EVM vs. Symbol, Occupied Bandwidth (OBW), Spectral Emission Mask (SEM), Constellation Diagram, and summary table with scalar results.

EVM (typical)

20 MHz 1CC, 256QAM UL, 30 kHz subcarrier spacing
400 MHz	650 MHz	1 GHz	2 GHz	3 GHz	3.5 GHz	5 GHz	6 GHz
1.15%	1.15%	1.28%	0.97%	1.13%	1.16%	1.08%	1.25%

<-37.4dB rms EVM from 400MHz to 6GHz for 20MHz CC1, 256QAM, -6dBm to -33dBm channel power, within -1dB of full scale.

ACLR (typical)

<-48dBc for <6GHz for 20MHz CC1, 256QAM, -6dBm to -27dBm channel power, within -1dB of full scale.

EMC pre-compliance and troubleshooting (EMCVUxx-SVPC)

Standards

EN55011, EN55012, EN55013, EN55014, EN55015, EN55025, EN55032, EN60601, DEF STAN, FCC Part 15, FCC Part18, MIL-STD 461G

Features

EMC-EMI display, Wizard to setup accessories and limit lines, Inspect, Harmonic Markers, Level Target, Compare Traces, Measure Ambient, Report generation, Re-measure Spot

Detectors

+Peak, Avg, Avg (of logs), Avg (VRMS), CISPR QuasiPeak, CISPR Peak, CISPR Average, CISPR Average of Logs, MIL +Peak, DEF STAN Avg, DEF STAN Peak

Limit lines

Up to 3 Limit Lines with corresponding margins

Resolution BW

Set per standard or user definable

Dwell time

Set per standard or user definable

Report format

PDF, HTML, MHT,RTF, XLSX, Image File format

Accessory type

Antenna, Near Field Probe, Cable, Amplifier, Limiter, Attenuator, Filter, Other

Correction format

Gain/Loss Constant, Gain/loss table, Antenna Factor

Traces

Save/recall up to 5 traces, Math trace (trace1 minus trace2), Ambient trace

Mapping (MAPxx-SVPC)

Supported map types

Pitney Bowes MapInfo (*.mif), Bitmap (*.bmp), Open Street Maps (.osm)

Saved measurement results

Measurement data files (exported results)

Map file used for the measurements

Google Earth KMZ file

Recallable results files (trace and setup files)

MapInfo-compatible MIF/MID files

Playback of recorded signals (SV56)

Playback file type

R3F recorded by RSA306, RSA500, or RSA600

Recorded file bandwidth

40 MHz

File playback controls

General: Play, stop, exit playback

Location: Begin/end points of playback settable from 0-100%

Skip: Defined skip size from 73 μs up to 99% of file size

Live rate: Plays back at 1:1 rate to recording time

Loop control: Play once, or loop continuously

Memory requirement

Recording of signals requires storage with write rates of 300 MB/sec. Playback of recorded files at live rates requires storage with read rates of 300 MB/sec.

RF input

Type N, female (RSA306B)

SMA, female (RSA306B-SMA)

External frequency reference input

SMA, female

Trigger/sync input

SMA, female

Status indicator

LED, dual color red/green

USB device port

USB 3.0 - Micro-B, can mate with locking thumbscrews

Power consumption

Per USB 3.0 SuperSpeed requirements: 5.0 V, ≤ 900 mA (nominal)

Dimensions

Dimensions	RSA306B	RSA306B-SMA (NO SHELL)	RSA306B-SMA (With SHELL)
Height	31.9 mm (1.25 in)	23.37 mm (0.92 in)	31.9 mm (1.25 in)
Width	190.5 mm (7.5 in)	176.5 mm (6.95 in)	178.56 mm (7.03 in)
Depth	139.7 mm (5.5 in)	120.9 mm (4.76 in)	140.97 mm (5.55 in)

Weight

RSA306B: 750 g (1.65 lbs)

RSA306B-SMA (with SHELL): 701.5 g (1.55 lbs)

RSA306B-SMA (NO SHELL): 571.5 g (1.26 lbs)

Regional certifications

Europe: EN61326

Australia/New Zealand: AS/NZS 2064

EMC emissions

EN61000-3-2, EN61000-3-3, EN61326-2-1

EMC immunity

EN61326–1/2, IEC61000-4-2/3/4/5/6/8/11

Temperature

Operating

-10 °C to +55 °C (+14 °F to +131 °F)

Nonoperating

-51 °C to +71 °C (-60 °F to +160 °F)

Humidity (operating)

5% to 75% ±5% relative humidity (RH) from +30 °C to +40 °C (+86 °F to 104 °F)

5% to 45% RH above +40 °C to +55 °C (+86 °F to +131 °F)

Altitude

Operating

Up to 9,144 meters (30,000 feet)

Nonoperating

15,240 meters (50,000 feet)

Dynamics³

Mechanical shock, operating

Half-sine mechanical shocks, 30 g peak amplitude, 11 μs duration, three drops in each direction of each axis (18 total)

Random vibration, nonoperating

0.030 g²/Hz, 10-500 Hz, 30 minutes per axis, three axes (90 minutes total)

Handling and transit1

Bench handling, operating

Per MIL-PRF-28800F Class 2 operating: Rotational-edge-drops of appropriate edges on appropriate sides of the equipment

Transit drop, nonoperating

Per MIL-PRF-28800F Class 2 nonoperating: Transit drops onto six faces and four corners of the equipment, from a height of 30 cm (11.8 in.) for a total of 10 impacts

RSA306B

RSA306B-SMA (SHELL)

RSA306B-SMA (NO SHELL)

USB real time spectrum analyzer, 9 kHz - 6.2 GHz, 40 MHz acquisition bandwidth.

The RSA306B requires a PC with Windows 7, Windows 8/8.1, or Windows 10, 64-bit operating system. A USB 3.0 connection is required for operation of the RSA306B. 8 GB RAM and 20 GB free drive space is required for installation of SignalVu-PC. For full performance of the real time features of the RSA306B, an Intel Core i7 4th generation processor is required. Processors of lower performance can be used, with reduced real-time performance.

Storage of streaming data requires that the PC be equipped with a drive capable of streaming storage rates of 300 MB/sec.

A variety of optional, licensed applications are available for purchase for SignalVu-PC. These licenses can be associated with and stored on either your PC or any RSA300 series, RSA500 series, RSA600 series, and RSA7100A spectrum analyzers. Licenses can be purchased as an option to your hardware, or separately as a Node-locked or a Floating license.

Contact your local Tektronix Account Manager to purchase a license. If your purchased license is not ordered as an option to your instrument, you will receive an email with a list of the applications purchased and the URL to the Tektronix Product License Web page, where you will create an account and can then manage your licenses using the Tektronix Asset Management System (AMS): http://www.tek.com/products/product-license.

AMS provides an inventory of the license(s) in your account. It enables you to check out or check in a license and view the history of licenses.

Optional applications are enabled by one of the following license types:

The following SignalVu-PC application licenses are available and add functionality and value to your measurement solution.

The Panasonic FZ-G1 Toughbook tablet controller is recommended for use with the RSA306B for portable field applications. The Windows 10 version of the tablet is available for purchase from Panasonic at https://na.panasonic.com/us/computers-tablets-handhelds/tablets/tablets/toughbook-g1 and other third party Web sites.

174-6796-xx

USB 3.0 locking cable (1 M)

063-4543-xx

SignalVu-PC software, documentation, USB key

071-3323-xx

Printed safety/installation manual (English)

RSA306B

3 years

RSA306B-SMA (SHELL)

3 years

RSA306B-SMA (NO SHELL)

3 years

Opt. C3

Calibration Service 3 Years

Opt. C5

Calibration Service 5 Years

Opt. D1

Calibration Data Report

Opt. D3

Calibration Data Report 3 Years (with Opt. C3)

Opt. D5

Calibration Data Report 5 Years (with Opt. C5)

Opt. R3

Repair Service 3 Years (including warranty)

Opt. R5

Repair Service 5 Years (including warranty)

NO SHELL

RSA306B-SMA sold without the black plastic outer shell

SHELL

RSA306B-SMA sold with the black plastic outer shell

MKIT

Mounting kit for mounting the RSA306B-SMA (NO SHELL option only). Available to customers in US and Canada only. Includes 6 qty standoffs, M-F, .312 HEX. 4-40 threading and medium thread locker.

Cables

174-6949-00

USB 3.0 locking cable, 0.5 m (half-length compared to USB cable shipped with the unit)

012-1738-00

Cable,50 Ohm, 40 Inch,Type-N(m) to Type-N(M)

012-0482-00

Cable, 50 Ω, BNC (m) 3 foot (91 cm)

Adapters

103-0045-00

Adapter, Coaxial, 50 Ohm Type-N(m) to Type BNC(f)

013-0410-00

Adapter, Coaxial, 50 Ohm Type-N (f) to Type-N (f)

013-0411-00

Adapter, Coaxial, 50 Ohm Type-N (m) to Type-N (f)

013-0412-00

Adapter, Coaxial, 50 Ohm, Type-N(m) to Type-N(m)

013-0402-00

Adapter, Coaxial, 50 Ohm Type-N (m) to Type-N 7/16(m)

013-0404-00

Adapter, Coaxial, 50 Ohm Type-N(m) to Type-7/16 (f)

013-0403-00

Adapter, Coaxial, 50 Ohm Type-N(m) to Type DIN 9.5(m)

013-0405-00

Adapter, Coaxial, 50 Ohm Type-N(m) to Type-DIN 9.5(f)

013-0406-00

Adapter, Coaxial, 50 Ohm Type-N(m) to Type-SMA(f)

013-0407-00

Adapter, Coaxial, 50 Ohm Type-N(m) to Type-SMA(m)

013-0408-00

Adapter, Coaxial, 50 Ohm Type-N(m) to Type-TNC(f)

013-0409-00

Adapter, Coaxial, 50 Ohm Type-N(m) to Type-TNC(m)

Attenuators and 50/75 Ω pads

013-0422-00

Pad, 50/75 Ohm, Minimum Loss, Type-N(m) 50 Ohm to Type-BNC(f) 75 Ohm

013-0413-00

Pad, 50/75 Ohm, Minimum Loss, Type-N(m) 50 Ohm to Type-BNC(m) 75 Ohm

013-0415-00

Pad, 50/75 Ohm, Minimum Loss, Type-N(m) 50 Ohm to Type-F(m) 75 Ohm

015-0787-00

Pad, 50/75 Ohm, Minimum Loss, Type-N(m) 50 Ohm to Type-F(f) 75 Ohm

015-0788-00

Pad, 50/75 Ohm, Minimum Loss, Type-N(m) 50 Ohm to Type-N(f) 75 Ohm

011-0222-00

Attenuator, Fixed, 10 dB, 2 W, DC-8 GHz, Type-N(f) to Type-N(f)

011-0223-00

Attenuator, Fixed, 10 dB, 2 W, DC-8 GHz, Type-N(m) to Type-N(f)

011-0224-00

Attenuator, Fixed, 10 dB, 2 W, DC-8 GHz, Type-N(m) to Type-N(m)

011-0228-00

Attenuator, Fixed, 3 dB, 2 W, DC-18 GHz, Type-N(m) to Type-N(f)

011-0225-00

Attenuator, Fixed, 40 dB, 100 W, DC-3 GHz, Type-N(m) to Type-N(f)

011-0226-00

Attenuator, Fixed, 40 dB, 50 W, DC-8.5 GHz, Type-N(m) to Type-N(f)

Antennas

119-6609-00

Flexible whip antenna, BNC-Male connector, PVC-coated, approximately 8 inches length. Center of sensitivity approximately 136 MHz, passband 5-1080 MHz

DF-A0047⁵

Directional Antenna, 20-8500 MHz, with electronic compass and preamp, available from http://www.alarisantennas.com

DF-A0047-011

Frequency range extension for DF-A0047 directional antenna, 9 kHz-20 MHz, available only from http://www.alarisantennas.com

DF-A0047-C11

Includes DF-A0047 antenna and DF-A0047-01 extension, available only from http://www.alarisantennas.com

016-2107-001

Transit case for DF-A0047 and DF-A0047-01, comes standard with purchase of DF-A0047, separately available only from http://www.alarisantennas.com

119-6594-00

Yagi Antenna, 825-896 MHz, Forward Gain (over half-wave dipole): 10 dB

119-6595-00

Yagi Antenna, 895-960 MHz, Forward Gain (over half-wave dipole): 10 dB

119-6596-00

Yagi Antenna, 1710-1880 MHz, Forward Gain (over half-wave dipole): 10.2 dB

119-6597-00

Yagi Antenna, 1850-1990 MHz, Forward Gain (over half-wave dipole): 9.3 dB

119-6970-00

Magnetic mount antenna, 824 MHz to 2170 MHz (requires adapter 103-0449-00)

EMC accessories

EMI-NF-PROBE

Near Field Probe set (Tekbox TBPS01)

Filters, probes, demonstration board

119-7246-00

Pre-filter, general purpose, 824 MHz to 2500 MHz, Type-N (f) connector

119-7426-00

Pre-filter, general purpose, 2400 MHz to 6200 MHz, Type-N (f) connector

119-4146-00

EMCO E/H-field probes. N-BNC adapter (103-0045-00) and 3 foot BNC cable (012-0482-00) recommended for use with probe kit

E/H field probes, lower cost alternative

Available from Beehive www. http://beehive-electronics.com/

(N-BNC adapter (103-0045-00) and 3 foot BNC cable (012-0482-00) recommended for use with probe kit)

011-0227-00

Bias-T, type N(m) RF, type N(f) RF+DC, BNC(f) Bias, 1 W, 0.5 A, 2.5 MHz-6 GHz