연락처

텍트로닉스 담당자와 실시간 상담 6:00am-4:30pm PST에 이용 가능

전화

전화 문의

9:00am-6:00PM KST에 이용 가능

다운로드

매뉴얼, 데이터 시트, 소프트웨어 등을 다운로드할 수 있습니다.

다운로드 유형
모델 또는 키워드

피드백

100G 광학 및 전기 Tx/Rx

텍트로닉스는 NRZ 및 PAM4 신호와 복합 코히런트(Coherent) 변조 형식에 대한 테스트 지침과 함께 100G 표준에 대한 포괄적인 Tx 및 Rx 테스트 지원을 제공합니다. 텍트로닉스의 테스트 장비로 당신의 팀은 향후의 datacom 기술을 활용할 기반을 갖출 수 있습니다.

  • DPO70000SX 시리즈 실시간 오실로스코프 는 기술 발전을 효율적으로 입증하고 100G 전기 기술 표준을 빠르게 디버깅하고 검증하는 기능을 제공합니다. 산업 수준의 낮은 노이즈 층과 높은 샘플링 속도에서 100G의 설계 성능을 확인해 보십시오.
    • 새로운 소식! MSO/DPO70000 범위에 대해 DPO7OE1 광 프로브 를 사용하면 PAM4 및 NRZ에 대한 소프트웨어 클럭 복구, 트리거링, 오류 감지 및 신호의 시간 상관 또는 연속 획득을 비롯한 강력한 디버그 기능을 추가하여 광 장치의 문제를 쉽게 해결할 수 있습니다.
  • DSA8300 시리즈 샘플링 오실로스코프 는 OSNR이 매우 낮은 업계 최고의 내장 광 기준 수신기를 사용하여 주요 단일 모드 광 표준을 충족하는 광 송신기 성능을 정확하게 특성화하는 데 적합합니다.
    • 새로운 소식! DSA8300용 80C17 및 80C18 광 모듈 은 생산 용량을 늘리고 프러덕션으로 전환되는 현재 100G 디자인의 수율을 향상시키는 새로운 기능과 함께 업계 최고의 마스크 테스트 민감도와 최저 광 노이즈를 제공합니다.
  • CR286A 클럭 리커버리 장비 는 대부분의 100Gbp/s 표준을 지원하며 텍트로닉스 샘플링 스코프 및 BERT와 연동되어 정확한 타이밍 측정 분석을 위한 안정적 클럭을 제공합니다.
  • BERTScope BSA 시리즈 비트 에러율 테스터 는 매우 정확한 BER 측정 결과 및 심층적인 근본 원인 분석 기능과 함께 긴 패턴의 PRBS 신호 생성 기능을 제공합니다.

 

주요 콘텐츠

Library

Title
Semtech Turns to Tektronix DSA8300 Sampling Scope to Characterize New 25-28 Gb/s CDR Devices
This customer case study illustrates the benefits that Tektronix DataCom test solutions deliver to characterize electrical performance of 100G technologies with the industry’s lowest intrinsic noise …
Clock Recovery Primer, Part 1
Part 1 of looking at clock recovery from a practical point of view with emphasis on how it affects measurements.
Characterizing an SFP+ Transceiver at the 16G Fibre Channel Rate
Study the measurements needed to test an SFP+ transceiver to the 16G Fibre Channel standard, covering both Multi- Mode 850 nm and Single Mode 1310 nm interfaces. Included is a test and …
Ultralow drive voltage silicon traveling-wave modulator Paper (Optical Society of America)
Silicon platforms are emerging as a commercial platform for integrated photonics. To integrate directly with on-chip electronics, drive voltages at or below 1 Vpp are desirable.In this paper from the …
Extinction Ratio (ER) Calibrated White Paper
This white paper explains some of the benefits of highly accurate ER measurements in both 10 GbE (Ethernet), with its relatively low ER requirement, and in SONET/ SDH , and the methodology that …
32 Gbit/s QPSK Transmission at 385 GHz
Learn more about a world record breaking wireless system capable of transmitting data at 400 GHz (0.4 THz) using advanced signal coding (up to QAM-16) and key advanced THz devices in this whitepaper …
Optical Bandwidth Requirements for NRZ and PAM4 Signaling
Until recently, both optical and electrical bandwidths produced similar results but this is no longer the case with the recent IEEE spec change. This paper clarifies these terms, mathematically shows …
Overcoming SNDR Measurement Challenges in 100G, 400G Datacom Testing
With important changes occurring in transmitter characterization and measurement methods for 100G and 400G standards (both IEEE and OIF-CEI) it is vital to learn more about SNDR and its advantages …
Practices for Measurements on 25 Gb/s Signaling
This application note describes the measurement practices for the characterization and compliance test of the transmitter and receiver for 25+ Gb/s signaling in 100 G systems. Focus is on oscilloscope …
Bridging the Gap Between BER and Eye Diagrams — A BER Contour Tutorial
BER Contour Measurement - What it is, how it is constructed, and why it is a valuable way of viewing parametric performance at gigabit speeds.
Coherent Optical Signal Generation with High-Performance AWG
Learn how instrument characteristics and performance level of the AWG70000 influence the ability to generate different modulation schemes and the way the instrument’s flexibility can be used to …
Physical Layer Tests of 100 Gb/s Communications Systems
In this application note, learn how to prepare for compliance measurements on 100G standards including IEEE802.3ba/bj/bm and the tests for optical, electrical, or PAM4 transmitters and receivers that …
100G/400G Datacom Transmitter Measurements: Determining Proper Measurement Tools for 100G/400G Datacom Testing
This application note walks through a number of common misconceptions and key considerations to help you select the proper scope technology (RTO vs. ETO) for your needs.
PAM4 Signaling in High Speed Serial Technology: Test, Analysis, and Debug
Learn valuable information on testing PAM4 technology and approaches for validating PAM4 signals.  This application note describes: PAM4 technology for 50-400G applications Provides details of PAM4 …
Title
Webinar: High Volume Optical Transceiver Validation
Learn about the current challenges in testing optical transceivers in a high volume manufacturing setting, and see a demonstration of a transceiver test system for PAM4 characterization using the …
Webinar: PAM4 Optical Transceiver Characterization
Watch as we discuss PAM4 optical transceivers, both 100G and 400G, including the latest on standards, testing, and characterization. We cover high throughput NRZ measurement and margin and compare …
New Technologies for Probing Low Power Circuits Webinar
As designs for mobile devices and computers use lower power circuits in their design, validation testing and debug become more challenging. Board and component density increase leaving little space …
PAM4 Electrical Webinar
The accelerated development of 400G Ethernet technology is driving new requirements through the test community as it relates to measuring electrical PAM4 systems. This presentation will review PAM4 …
NBASET and IEEE8023bz Technology and Measurements
The rapid growth of ever-more powerful mobile devices, and the adoption of new wireless technologies such as 802.11ac, has enterprise networks struggling to keep pace. To meet these rising bandwidth …
Characterizing Coherent Optical Systems Webinar
Learn about the coherent modulation being considered for 400G networks, the key building blocks of a coherent test system, how to optimize measurement accuracy and the benefits of customizable …